It is suitable for hydraulic transmission of construction machinery, lifting, transportation machinery and mining machinery. Hydraulic transmission principle - oil is used as working medium, Huzhou Hydraulic cylinder The movement is transmitted through the change of sealing volume, and the power is transmitted through the pressure inside the oil. 1. Power part - converts mechanical energy of prime mover into pressure energy (hydraulic energy) of oil. For example: hydraulic pump. 2. Executive part - converts the oil pressure energy input by the hydraulic pump into the mechanical energy driving the working mechanism. For example: hydraulic cylinder, hydraulic motor. 3. Control part - used to control and adjust the oil pressure Huzhou Hydraulic cylinder manufactor Flow rate and flow direction. For example: pressure control valve, flow control valve.

How to install and fix the hydraulic cylinder? There are two common ways to fix the hydraulic cylinder: the first is the square hydraulic cylinder fixed on the B plate, and the hydraulic cylinder needs to be positioned on the B plate. The second is a round hydraulic cylinder fixed on the ejector plate. It should be noted that the thimble plate locking screw needs to be added next to the hydraulic cylinder, and the force at this position is large, Huzhou Hydraulic cylinder Prevent tension deformation. Another point is to inscribe words on the hydraulic cylinder, and write down the stroke of the hydraulic cylinder for easy verification. To correctly install the sealing device at each position of the hydraulic cylinder: Huzhou Hydraulic cylinder manufactor When installing the O-ring seal, pay attention to its installation direction to avoid oil leakage due to installation. Its lip should face the oil chamber with pressure.

The two lips of the seal have two contact circumferential surfaces. Whether the force on the inner and outer circumferences is evenly distributed means that the force on the two circumferences cannot be zero. If the force on a certain point is zero, the shaft seal has inner and outer lips, Huzhou Hydraulic cylinder The outer lip is installed in the groove to contact the outer wall, and the inner lip is in contact with the piston rod surface. Both lips have an interference amount, which is equal to the generation of two contact circumferential surfaces, that is, the generation of two circumferential rebound forces. How to determine the magnitude of the circumferential force? Both the inner and outer lips of the seal have two chamfers. Since the interference of the same inner and outer lips is certain, Huzhou Hydraulic cylinder manufactor The angle of the chamfer determines the size of the circumferential area of the inner and outer contact of the two lips.

Because the hydraulic cylinder has to bear a great pressure, the heavier the load, the greater its pressure will be. Therefore, the maintenance of the hydraulic cylinder is an important part of the maintenance of the entire hydraulic system. The hydraulic cylinder is the heart of the hydraulic system, Huzhou Hydraulic cylinder It is difficult to repair the heart problem, so the maintenance of the hydraulic cylinder should be careful. First, rust prevention. Because the piston part of the hydraulic cylinder will extend the cylinder in the working state, Huzhou Hydraulic cylinder manufactor Naturally, it will be corroded by oxide and acid gas, which requires us to coat it with proper grease for protection.

The oil cylinder shall be assembled in a special workshop or assembly area, and the temperature shall be kept at 20~250C, Huzhou Hydraulic cylinder manufactor It shall be far away from the tuyere, dust and cutting area, with fresh air, no dust and no noise; Avoid direct glare. The assembly room shall be equipped with installation platform, sufficient working position apparatus, assembly turnover vehicle Huzhou Hydraulic cylinder Lifting and hoisting equipment and the following special basic equipment. a: Cylinder loader; b: Another cylinder cleaning machine is used to heat and clean another part; c: Pressure test equipment, used for pressure test of oil cylinder; d: The air duct is used to clean and dry the other parts after cleaning.

The valve core of the flow valve in the hydraulic cylinder is blocked, which is easy to cause the action failure of the hydraulic cylinder. We need to check whether there are pollutants in the oil in the hydraulic cylinder and whether the valve body is worn. It is necessary to check whether the piston rod seal is too tight, Huzhou Hydraulic cylinder Whether there are pollutants entering, whether the axis line is aligned, and whether the easily damaged components fail. If the pressure controlled by the hydraulic system is too low, the action of the hydraulic cylinder will also fail, Huzhou Hydraulic cylinder manufactor At this time, it is necessary to check the control pressure source to ensure that the pressure value is consistent with the specified value of the system.