How to install and fix the hydraulic cylinder? There are two common ways to fix the hydraulic cylinder: the first is the square hydraulic cylinder fixed on the B plate, and the hydraulic cylinder needs to be positioned on the B plate. The second is a round hydraulic cylinder fixed on the ejector plate. It should be noted that the thimble plate locking screw needs to be added next to the hydraulic cylinder, and the force at this position is large, Hebei Hydraulic machinery Prevent tension deformation. Another point is to inscribe words on the hydraulic cylinder, and write down the stroke of the hydraulic cylinder for easy verification. To correctly install the sealing device at each position of the hydraulic cylinder: Hebei Hydraulic machinery Manufacturer When installing the O-ring seal, pay attention to its installation direction to avoid oil leakage due to installation. Its lip should face the oil chamber with pressure.

For the same hydraulic cylinder on the Internet, some manufacturers quote more than 1200, some more than 1600, some about 1800, and even some about 3000. This situation makes the purchasing manufacturers feel puzzled and very difficult. Most manufacturers have limited procurement funds, Hebei Hydraulic machinery Therefore, if you want to achieve the predetermined purchase goal, you need to choose the hydraulic cylinder with high cost performance ratio, good quality and low price. However, the price gap of hydraulic cylinders in the market is staggering, Hebei Hydraulic machinery Manufacturer If you choose cheap oil cylinder rashly, the quality cannot be guaranteed, which will lead to endless troubles.

The speed ratio refers to the same flow (volume of liquid entering the hydraulic cylinder per unit time), Hebei Hydraulic machinery Manufacturer The ratio of the piston rod extension speed to the retraction speed. The calculation is equal to the inverse ratio of the large cavity area and the small cavity area of the cylinder. The speed ratio is related to the cylinder diameter and rod diameter of the oil cylinder. Main products: harvesting machinery series Hebei Hydraulic machinery Flip plow series, press series, grader series, TGL, HG, SG, DG series vehicle oil cylinder, HSG series engineering oil cylinder mining machinery, ship oil cylinder, and various non-standard oil cylinders. Welcome to order!

Hydraulic cylinder is a hydraulic actuator that converts hydraulic energy into mechanical energy and performs linear reciprocating motion (or swing motion). It is simple in structure and reliable in operation. When it is used to realize reciprocating movement, the reducer can be avoided, Hebei Hydraulic machinery And there is no transmission clearance, smooth movement, so it is widely used in various mechanical hydraulic systems. Output force of the hydraulic cylinder is proportional to effective area of the piston and pressure difference on both sides; The hydraulic cylinder basically consists of cylinder barrel, cylinder head Hebei Hydraulic machinery Manufacturer The piston and piston rod, sealing device, buffer device and exhaust device are composed.

For the selection of hydraulic cylinder, the hydraulic cylinder will be selected according to the inner diameter, stroke, operating pressure and installation type during the selection of hydraulic cylinder. In fact, in addition to these, we should pay attention to the following points. First, when the hydraulic cylinder is loaded and then the actuating speed reaches a certain standard, Hebei Hydraulic machinery Hydraulic cylinder with buffer device must be used. Or when the speed reaches a higher speed, a deceleration valve must be installed outside the hydraulic cylinder; Secondly, carefully select hydraulic oil and oil seal. Oil seals of different materials are selected for different hydraulic oils, Hebei Hydraulic machinery Manufacturer To ensure the service life of the hydraulic cylinder.

As the structure and size of various hydraulic cylinders are different, the disassembly sequence is slightly different. Generally, drain the oil in the two chambers of the oil cylinder, remove the cylinder head, and finally remove the piston and piston rod. Hebei Hydraulic machinery When disassembling the cylinder head of the hydraulic cylinder, special tools shall be used for the key or snap ring of the internal key type connection, and flat shovel is prohibited; Flange end caps must be pushed out with screws, and hammering or hard prying is not allowed. When it is difficult to draw out the piston and piston rod, do not force them out, Hebei Hydraulic machinery Manufacturer The reason shall be found out before disassembly. Before and after unloading, try to create conditions to prevent the parts of the hydraulic cylinder from being polluted by the surrounding dust and impurities.