上海新茶外卖高端

 Hydraulic cylinder manufacturer
Your current location: home page > Hot information

contact us Contact Us

Foshan Fuchao Hydraulic Electromechanical Equipment Co., Ltd

Mobile: 15975751599

Mobile: 13531395368

Tel.: 0757-85131606

Email: [email protected]

Website: uonetech.com.cn

Address: No. 26 and 27, Road 9, Zone 2, Xiedei Bridge, Guidan Avenue, Xiebian Second Industrial Zone, Dali Town, Nanhai District, Foshan City

Ningxia customized oil cylinder manufacturer

2021-08-22
 Ningxia customized oil cylinder manufacturer

The diameter of the oil unloading hole of the hydraulic cylinder is too large, which directly affects the service life of the rubber seal ring on the piston. Because the piston moves back and forth, Ningxia Oil cylinder When the rubber seal ring on the piston passes through the oil discharge hole, the rubber's own elasticity expands to the oil discharge hole, and the oil discharge hole edge and the piston seal groove edge shear the rubber seal ring. At the same time, China has the advantages of strong market demand and low cost, and is expected to become the center of gravity of the world's hydraulic industry and oil cylinder industry in the future. The hydraulic cylinder is a very important part of the hydraulic machinery and plays an executive role in the entire hydraulic machinery, Ningxia Oil cylinder Manufacturer In the whole process, the hydraulic cylinder converts hydraulic energy into mechanical energy.

 Ningxia customized oil cylinder manufacturer

The hydraulic cylinder is the actuating element that converts hydraulic energy into mechanical energy in the hydraulic system. The faults can be basically summarized as hydraulic cylinder misoperation Ningxia Oil cylinder Manufacturer It is unable to push the load and the piston slips or crawls. It is not uncommon for hydraulic cylinder failure to cause equipment shutdown. Therefore, Ningxia Oil cylinder Attention should be paid to the fault diagnosis, use and maintenance of hydraulic cylinder. The main reason for excessive wear of piston seals is that the speed control valve is improperly adjusted, resulting in excessive back pressure, improper installation of seals or contamination of hydraulic oil. Secondly, foreign matters enter during assembly and the quality of sealing materials is poor.

 Ningxia customized oil cylinder manufacturer

The failure of the hydraulic cylinder due to improper design and manufacture is because the oil pressure cannot act on the effective working area of the piston when the piston travels to the end point and returns, or the effective working area is too small when starting, which causes problems. When the transverse load of the hydraulic cylinder is too large, the force is not strong or the cylinder is bitten, the same consequences will occur. Ningxia Oil cylinder Therefore, when installing the hydraulic cylinder, the axis position of the cylinder must be consistent with the movement direction; Ningxia Oil cylinder Manufacturer And ensure that the load borne by the hydraulic cylinder passes through the cylinder axis as far as possible without eccentricity, so that the problem can be solved.

 Ningxia customized oil cylinder manufacturer

Because the hydraulic cylinder must bear a great pressure, the heavier the load, the greater its pressure will be. Therefore, the maintenance of the hydraulic cylinder is the most important part of the maintenance of the entire hydraulic system. The hydraulic cylinder is the heart of the hydraulic system. It is difficult to repair a heart problem, so the maintenance of the hydraulic cylinder should be careful. first, Ningxia Oil cylinder Rust prevention is required. Because the piston part of the hydraulic cylinder will extend out of the cylinder in the working state, it will naturally suffer from oxidation Ningxia Oil cylinder Manufacturer The erosion of acid gas requires us to apply proper amount of grease to protect it.

 Ningxia customized oil cylinder manufacturer

For the selection of hydraulic cylinder, the hydraulic cylinder will be selected according to the inner diameter, stroke, operating pressure and installation type during the selection of hydraulic cylinder. In fact, in addition to these, we should pay attention to the following points. First, when the hydraulic cylinder is loaded and then the actuating speed reaches a certain standard, Ningxia Oil cylinder Hydraulic cylinder with buffer device must be used. Or when the speed reaches a higher speed, a deceleration valve must be installed outside the hydraulic cylinder; Secondly, carefully select hydraulic oil and oil seal. Oil seals of different materials are selected for different hydraulic oils, Ningxia Oil cylinder Manufacturer To ensure the service life of the hydraulic cylinder.

home page             About us             Product display             Success stories             after-sale service             News Center             contact us

contact information           Site Map           Online Message

Tel: 15975751599/13531395368

Service hotline: 0757-85131606

Email: [email protected]

Address: No. 26 and 27, Road 9, Zone 2, Xiedei Bridge, Guidan Avenue, Xiebian Second Industrial Zone, Dali Town, Nanhai District, Foshan City

 Oil cylinder manufacturer

Service, service, heat and line

159-7575-1599

135-3139-5368

Copyright © Foshan Fuchao Hydraulic Electromechanical Equipment Co., Ltd. All rights reserved is mainly engaged in Oil cylinder manufacturer , Hydraulic cylinder manufacturer , Oil cylinder manufacturer Welcome to inquire!
Record No.: Service support: Statement: Part of the content and pictures of this site are from the Internet. If there is infringement, please contact the administrator to delete it at the first time. Thank you!
Main business area: Foshan Shenzhen Guangzhou Zhongshan Guangdong Zhuhai Dongguan Huizhou Guangxi Beijing