Because the hydraulic cylinder must bear a great pressure, the heavier the load, the greater its pressure will be. Therefore, the maintenance of the hydraulic cylinder is the most important part of the maintenance of the entire hydraulic system. The hydraulic cylinder is the heart of the hydraulic system. It is difficult to repair a heart problem, so the maintenance of the hydraulic cylinder should be careful. first, Yinchuan Hydraulic cylinder Rust prevention is required. Because the piston part of the hydraulic cylinder will extend out of the cylinder in the working state, it will naturally suffer from oxidation Yinchuan Hydraulic cylinder manufactor The erosion of acid gas requires us to apply proper amount of grease to protect it.

Hydraulic oil cylinder is used in many industries. Once it fails, it will have a far-reaching impact and hinder the progress of all work. In fact, many customers said that the hydraulic cylinder could not operate, Yinchuan Hydraulic cylinder In order to solve this problem in time, we should first find out what causes the problem. Generally speaking, the problem that the hydraulic cylinder cannot act often occurs on the newly installed hydraulic cylinder, Yinchuan Hydraulic cylinder manufactor Generally, it is necessary to start from external reasons, such as whether the mechanism pulled by the hydraulic cylinder has excessive resistance, whether it is stuck, and whether it is against other parts; Whether the pressure at the oil inlet of the hydraulic cylinder is within the specified range.

The two lips of the seal have two contact circumferential surfaces. Whether the force on the inner and outer circumferences is evenly distributed means that the force on the two circumferences cannot be zero. If the force on a certain point is zero, the shaft seal has inner and outer lips, Yinchuan Hydraulic cylinder The outer lip is installed in the groove to contact the outer wall, and the inner lip is in contact with the piston rod surface. Both lips have an interference amount, which is equal to the generation of two contact circumferential surfaces, that is, the generation of two circumferential rebound forces. How to determine the magnitude of the circumferential force? Both the inner and outer lips of the seal have two chamfers. Since the interference of the same inner and outer lips is certain, Yinchuan Hydraulic cylinder manufactor The angle of the chamfer determines the size of the circumferential area of the inner and outer contact of the two lips.

Select the cylinder type correctly according to the working requirements and conditions. It is required that there is no impact phenomenon and impact noise when the cylinder reaches the end of the stroke; Cushion cylinder shall be selected; Light weight is required; It is required to select light cylinder; Yinchuan Hydraulic cylinder Narrow installation space and short stroke are required; It is required to select thin cylinder; It is required to have transverse load, and the cylinder with guide rod can be selected; High braking accuracy is required, and locking cylinder can be selected; It is not allowed to rotate the piston rod, and the cylinder with rod non rotation function can be selected; Yinchuan Hydraulic cylinder manufactor In corrosive environment, corrosion-resistant steel cylinders shall be selected.

1. Internal leakage of oil cylinder; 2. Internal leakage at control valve hole and valve rod; 3. Overload overflow valve is poor; 4. The valve rod is not in the middle position; 5. PPC valve is not in the middle position. Hydraulic cylinder maintenance process: 1. Whether the hydraulic lock becomes normal when it is in the determined position, if so, check the PPC valve first; 2. Conduct oil cylinder plugging oil port test, Yinchuan Hydraulic cylinder Check whether the oil cylinder is defective, and repair the oil cylinder if it is; 3. Replace the overload overflow valve and check whether it is the fault of the overload overflow valve; 4. Whether the valve rod is jammed, Yinchuan Hydraulic cylinder manufactor Check again after cleaning, otherwise the main control valve needs to be repaired.

1、 If the groove is too deep, two situations will occur: A. If the gap between the seal root and the groove becomes larger, the seal root will become unstable. B. The interference between the sealing lip and the sealing surface becomes smaller, Yinchuan Hydraulic cylinder The rebound force of the seal becomes smaller, and the failure rate of low-pressure oil leakage will increase when the piston rod jumps. 2、 If the groove is too shallow, two situations will also occur: A. The interference between the sealing lip and the sealing surface will increase, and the contact area will increase, which will lead to greater friction, Yinchuan Hydraulic cylinder manufactor The increased heat accelerates the damage of the seal lip. B. As a result, the clearance at the seal root becomes smaller, and the probability of the seal root being squeezed out when the oil cylinder is under high pressure increases.