The failure of the hydraulic cylinder due to improper design and manufacture is because the oil pressure cannot act on the effective working area of the piston when the piston travels to the end point and returns, or the effective working area is too small when starting, which causes problems. When the transverse load of the hydraulic cylinder is too large, the force is not strong or the cylinder is bitten, the same consequences will occur. Baotou Hydraulic cylinder Therefore, when installing the hydraulic cylinder, the axis position of the cylinder must be consistent with the movement direction; Baotou Hydraulic cylinder manufactor And ensure that the load borne by the hydraulic cylinder passes through the cylinder axis as far as possible without eccentricity, so that the problem can be solved.

Items to be checked when the speed of hydraulic cylinder slows down. 1. Where and what type of oil cylinder has been used for several years, Baotou Hydraulic cylinder What is the working pressure. You don't have any of these. How can I troubleshoot them for you. Check the lower seal if there is internal leakage. 2. It is likely that the internal working pressure of the oil cylinder has decreased. 3. Check whether the system is blocked, Baotou Hydraulic cylinder manufactor In addition, check whether the oil cylinder seal ring is damaged, and then check whether the piston rod is damaged. Basically, these aspects can identify the problem.

The connection between the oil cylinder and the actuator and the connection between the oil cylinder and the oil pipe cannot be the same, because there must be some differences between the connection between the oil cylinder and different products. In addition, during the use of the oil cylinder, it is necessary to avoid scratches, Baotou Hydraulic cylinder Because if this problem occurs, it will affect the normal use of the oil cylinder. At present, there is no software for designing hydraulic cylinders, but there are design standards for hydraulic cylinders, and it is necessary to design hydraulic cylinders according to these standards. So far, Baotou Hydraulic cylinder manufactor There is no software for designing hydraulic cylinders, but there are design standards for hydraulic cylinders.

The two lips of the seal have two contact circumferential surfaces. Whether the force on the inner and outer circumferences is evenly distributed means that the force on the two circumferences cannot be zero. If the force on a certain point is zero, the shaft seal has inner and outer lips, Baotou Hydraulic cylinder The outer lip is installed in the groove to contact the outer wall, and the inner lip is in contact with the piston rod surface. Both lips have an interference amount, which is equal to the generation of two contact circumferential surfaces, that is, the generation of two circumferential rebound forces. How to determine the magnitude of the circumferential force? Both the inner and outer lips of the seal have two chamfers. Since the interference of the same inner and outer lips is certain, Baotou Hydraulic cylinder manufactor The angle of the chamfer determines the size of the circumferential area of the inner and outer contact of the two lips.

Because the hydraulic cylinder must bear a great pressure, the heavier the load, the greater its pressure will be. Therefore, the maintenance of the hydraulic cylinder is the most important part of the maintenance of the entire hydraulic system. The hydraulic cylinder is the heart of the hydraulic system. It is difficult to repair a heart problem, so the maintenance of the hydraulic cylinder should be careful. first, Baotou Hydraulic cylinder Rust prevention is required. Because the piston part of the hydraulic cylinder will extend out of the cylinder in the working state, it will naturally suffer from oxidation Baotou Hydraulic cylinder manufactor The erosion of acid gas requires us to apply proper amount of grease to protect it.

The diameter of the oil unloading hole of the hydraulic cylinder is too large, which directly affects the service life of the rubber seal ring on the piston. Because the piston moves back and forth, Baotou Hydraulic cylinder When the rubber seal ring on the piston passes through the oil discharge hole, the rubber's own elasticity expands to the oil discharge hole, and the oil discharge hole edge and the piston seal groove edge shear the rubber seal ring. At the same time, China has the advantages of strong market demand and low cost, and is expected to become the center of gravity of the world's hydraulic industry and oil cylinder industry in the future. The hydraulic cylinder is a very important part of the hydraulic machinery and plays an executive role in the entire hydraulic machinery, Baotou Hydraulic cylinder manufactor In the whole process, the hydraulic cylinder converts hydraulic energy into mechanical energy.