The diameter of the oil unloading hole of the hydraulic cylinder is too large, which directly affects the service life of the rubber seal ring on the piston. Because the piston moves back and forth, Tibet Hydraulic cylinder When the rubber seal ring on the piston passes through the oil discharge hole, the rubber's own elasticity expands to the oil discharge hole, and the oil discharge hole edge and the piston seal groove edge shear the rubber seal ring. At the same time, China has the advantages of strong market demand and low cost, and is expected to become the center of gravity of the world's hydraulic industry and oil cylinder industry in the future. The hydraulic cylinder is a very important part of the hydraulic machinery and plays an executive role in the entire hydraulic machinery, Tibet Hydraulic cylinder manufactor In the whole process, the hydraulic cylinder converts hydraulic energy into mechanical energy.

As the structure and size of various hydraulic cylinders are different, the disassembly sequence is slightly different. Generally, drain the oil in the two chambers of the oil cylinder, remove the cylinder head, and finally remove the piston and piston rod. Tibet Hydraulic cylinder When disassembling the cylinder head of the hydraulic cylinder, special tools shall be used for the key or snap ring of the internal key type connection, and flat shovel is prohibited; Flange end caps must be pushed out with screws, and hammering or hard prying is not allowed. When it is difficult to draw out the piston and piston rod, do not force them out, Tibet Hydraulic cylinder manufactor The reason shall be found out before disassembly. Before and after unloading, try to create conditions to prevent the parts of the hydraulic cylinder from being polluted by the surrounding dust and impurities.

The hydraulic cylinder is the actuating element that converts hydraulic energy into mechanical energy in the hydraulic system. The faults can be basically summarized as hydraulic cylinder misoperation Tibet Hydraulic cylinder manufactor It is unable to push the load and the piston slips or crawls. It is not uncommon for hydraulic cylinder failure to cause equipment shutdown. Therefore, Tibet Hydraulic cylinder Attention should be paid to the fault diagnosis, use and maintenance of hydraulic cylinder. The main reason for excessive wear of piston seals is that the speed control valve is improperly adjusted, resulting in excessive back pressure, improper installation of seals or contamination of hydraulic oil. Secondly, foreign matters enter during assembly and the quality of sealing materials is poor.

For the selection of hydraulic cylinder, the hydraulic cylinder will be selected according to the inner diameter, stroke, operating pressure and installation type during the selection of hydraulic cylinder. In fact, in addition to these, we should pay attention to the following points. First, when the hydraulic cylinder is loaded and then the actuating speed reaches a certain standard, Tibet Hydraulic cylinder Hydraulic cylinder with buffer device must be used. Or when the speed reaches a higher speed, a deceleration valve must be installed outside the hydraulic cylinder; Secondly, carefully select hydraulic oil and oil seal. Oil seals of different materials are selected for different hydraulic oils, Tibet Hydraulic cylinder manufactor To ensure the service life of the hydraulic cylinder.

Compared with mechanical transmission, hydraulic cylinder transmission is a new transmission form. Hydraulic transmission has a history of more than 200 years since the birth of hydraulic press, but hydraulic transmission has been going on for many years. Especially after the 1960s, with the development of atomic energy science, space and hydraulic technology, Tibet Hydraulic cylinder It permeates all fields of the national economy, including agricultural machinery, automobiles, light textile, shipbuilding, petroleum, aviation and machine tool industries, Tibet Hydraulic cylinder manufactor Hydraulic technology lists some application examples of hydraulic and pneumatic transmission.

1、 If the groove is too deep, two situations will occur: A. If the gap between the seal root and the groove becomes larger, the seal root will become unstable. B. The interference between the sealing lip and the sealing surface becomes smaller, Tibet Hydraulic cylinder The rebound force of the seal becomes smaller, and the failure rate of low-pressure oil leakage will increase when the piston rod jumps. 2、 If the groove is too shallow, two situations will also occur: A. The interference between the sealing lip and the sealing surface will increase, and the contact area will increase, which will lead to greater friction, Tibet Hydraulic cylinder manufactor The increased heat accelerates the damage of the seal lip. B. As a result, the clearance at the seal root becomes smaller, and the probability of the seal root being squeezed out when the oil cylinder is under high pressure increases.