There are many hydraulic components on construction machinery, and sufficient hydraulic oil is required. When the hydraulic oil needs to be replaced due to its deterioration after a long time of use, some people mistakenly believe that it is only necessary to drain the oil in the hydraulic cylinder Gansu Hydraulic station Top up with new hydraulic oil. However, there are still many old hydraulic oils left in the hydraulic oil pipe and hydraulic control valve at this time. When the equipment is used, the mixing of new and old oils will speed up the deterioration of new oils. The correct oil change procedure should first drain the hydraulic oil in the hydraulic cylinder, clean the hydraulic cylinder, and then add new hydraulic oil, Gansu Hydraulic station Price Then remove the circuit header, start the engine and run at low speed to make the oil pump work and operate each mechanism separately.

As the structure and size of various hydraulic cylinders are different, the disassembly sequence is slightly different. Generally, drain the oil in the two chambers of the oil cylinder, remove the cylinder head, and finally remove the piston and piston rod. Gansu Hydraulic station When disassembling the cylinder head of the hydraulic cylinder, special tools shall be used for the key or snap ring of the internal key type connection, and flat shovel is prohibited; Flange end caps must be pushed out with screws, and hammering or hard prying is not allowed. When it is difficult to draw out the piston and piston rod, do not force them out, Gansu Hydraulic station Price The reason shall be found out before disassembly. Before and after unloading, try to create conditions to prevent the parts of the hydraulic cylinder from being polluted by the surrounding dust and impurities.

For the same hydraulic cylinder on the Internet, some manufacturers quote more than 1200, some more than 1600, some about 1800, and even some about 3000. This situation makes the purchasing manufacturers feel puzzled and very difficult. Most manufacturers have limited procurement funds, Gansu Hydraulic station Therefore, if you want to achieve the predetermined purchase goal, you need to choose the hydraulic cylinder with high cost performance ratio, good quality and low price. However, the price gap of hydraulic cylinders in the market is staggering, Gansu Hydraulic station Price If you choose cheap oil cylinder rashly, the quality cannot be guaranteed, which will lead to endless troubles.

For the selection of hydraulic cylinder, the hydraulic cylinder will be selected according to the inner diameter, stroke, operating pressure and installation type during the selection of hydraulic cylinder. In fact, in addition to these, we should pay attention to the following points. First, when the hydraulic cylinder is loaded and then the actuating speed reaches a certain standard, Gansu Hydraulic station Hydraulic cylinder with buffer device must be used. Or when the speed reaches a higher speed, a deceleration valve must be installed outside the hydraulic cylinder; Secondly, carefully select hydraulic oil and oil seal. Oil seals of different materials are selected for different hydraulic oils, Gansu Hydraulic station Price To ensure the service life of the hydraulic cylinder.

Hydraulic cylinder is a hydraulic actuator that converts hydraulic energy into mechanical energy and performs linear reciprocating motion (or swing motion). It is simple in structure and reliable in operation. When it is used to realize reciprocating movement, the reducer can be avoided, Gansu Hydraulic station And there is no transmission clearance, smooth movement, so it is widely used in various mechanical hydraulic systems. Output force of the hydraulic cylinder is proportional to effective area of the piston and pressure difference on both sides; The hydraulic cylinder basically consists of cylinder barrel, cylinder head Gansu Hydraulic station Price The piston and piston rod, sealing device, buffer device and exhaust device are composed.

There are many hydraulic components on construction machinery, and sufficient hydraulic oil is required. When the hydraulic oil needs to be replaced due to its deterioration after a long time of use, some people mistakenly believe that only drain the oil in the hydraulic cylinder and fill it with new hydraulic oil. However, there are still many old hydraulic oils left in the hydraulic oil pipe and hydraulic control valve, Gansu Hydraulic station When the equipment is used, the mixing of new and old oil will speed up the deterioration of new oil. The correct oil change procedure should first drain the hydraulic oil in the hydraulic cylinder, Gansu Hydraulic station Price After cleaning the hydraulic cylinder, add new hydraulic oil, remove the circuit header, start the engine and run at low speed to make the oil pump work.