The oil cylinder shall be assembled in a special workshop or assembly area, and the temperature shall be kept at 20~250C, Guangxi Hydraulic system Manufacturer It shall be far away from the tuyere, dust and cutting area, with fresh air, no dust and no noise; Avoid direct glare. The assembly room shall be equipped with installation platform, sufficient working position apparatus, assembly turnover vehicle Guangxi Hydraulic system Lifting and hoisting equipment and the following special basic equipment. a: Cylinder loader; b: Another cylinder cleaning machine is used to heat and clean another part; c: Pressure test equipment, used for pressure test of oil cylinder; d: The air duct is used to clean and dry the other parts after cleaning.
For the selection of hydraulic cylinder, the hydraulic cylinder will be selected according to the inner diameter, stroke, operating pressure and installation type during the selection of hydraulic cylinder. In fact, in addition to these, we should pay attention to the following points. First, when the hydraulic cylinder is loaded and then the actuating speed reaches a certain standard, Guangxi Hydraulic system Hydraulic cylinder with buffer device must be used. Or when the speed reaches a higher speed, a deceleration valve must be installed outside the hydraulic cylinder; Secondly, carefully select hydraulic oil and oil seal. Oil seals of different materials are selected for different hydraulic oils, Guangxi Hydraulic system Manufacturer To ensure the service life of the hydraulic cylinder.
There are many hydraulic components on construction machinery, and sufficient hydraulic oil is required. When the hydraulic oil needs to be replaced due to its deterioration after a long time of use, some people mistakenly believe that only drain the oil in the hydraulic cylinder and fill it with new hydraulic oil. However, there are still many old hydraulic oils left in the hydraulic oil pipe and hydraulic control valve, Guangxi Hydraulic system When the equipment is used, the mixing of new and old oil will speed up the deterioration of new oil. The correct oil change procedure should first drain the hydraulic oil in the hydraulic cylinder, Guangxi Hydraulic system Manufacturer After cleaning the hydraulic cylinder, add new hydraulic oil, remove the circuit header, start the engine and run at low speed to make the oil pump work.
Two way hydraulic cylinder, which is one of the hydraulic cylinders, is a common and commonly used type of hydraulic cylinder. Therefore, Guangxi Hydraulic system Manufacturer It is necessary to have a correct understanding of this kind of hydraulic cylinder and have a certain understanding, so that we can know how to use it reasonably and make full use of it. This kind of hydraulic cylinder has corresponding operation regulations and maintenance regulations, because it is in the hydraulic cylinder category. In addition, Guangxi Hydraulic system It is necessary to have a clear and comprehensive understanding of its operation and maintenance procedures. The symptom of strain and wear is that the lifting speed of the equipment is relatively slow, accompanied by self subsidence.
How to install and fix the hydraulic cylinder? There are two common ways to fix the hydraulic cylinder: the first is the square hydraulic cylinder fixed on the B plate, and the hydraulic cylinder needs to be positioned on the B plate. The second is a round hydraulic cylinder fixed on the ejector plate. It should be noted that the thimble plate locking screw needs to be added next to the hydraulic cylinder, and the force at this position is large, Guangxi Hydraulic system Prevent tension deformation. Another point is to inscribe words on the hydraulic cylinder, and write down the stroke of the hydraulic cylinder for easy verification. To correctly install the sealing device at each position of the hydraulic cylinder: Guangxi Hydraulic system Manufacturer When installing the O-ring seal, pay attention to its installation direction to avoid oil leakage due to installation. Its lip should face the oil chamber with pressure.
1. Internal leakage of oil cylinder; 2. Internal leakage at control valve hole and valve rod; 3. Overload overflow valve is poor; 4. The valve rod is not in the middle position; 5. PPC valve is not in the middle position. Hydraulic cylinder maintenance process: 1. Whether the hydraulic lock becomes normal when it is in the determined position, if so, check the PPC valve first; 2. Conduct oil cylinder plugging oil port test, Guangxi Hydraulic system Check whether the oil cylinder is defective, and repair the oil cylinder if it is; 3. Replace the overload overflow valve and check whether it is the fault of the overload overflow valve; 4. Whether the valve rod is jammed, Guangxi Hydraulic system Manufacturer Check again after cleaning, otherwise the main control valve needs to be repaired.
