1、 If the groove is too deep, two situations will occur: A. If the gap between the seal root and the groove becomes larger, the seal root will become unstable. B. The interference between the sealing lip and the sealing surface becomes smaller, Harbin Hydraulic equipment The rebound force of the seal becomes smaller, and the failure rate of low-pressure oil leakage will increase when the piston rod jumps. 2、 If the groove is too shallow, two situations will also occur: A. The interference between the sealing lip and the sealing surface will increase, and the contact area will increase, which will lead to greater friction, Harbin Hydraulic equipment Price The increased heat accelerates the damage of the seal lip. B. As a result, the clearance at the seal root becomes smaller, and the probability of the seal root being squeezed out when the oil cylinder is under high pressure increases.

For the selection of hydraulic cylinder, the hydraulic cylinder will be selected according to the inner diameter, stroke, operating pressure and installation type during the selection of hydraulic cylinder. In fact, in addition to these, we should pay attention to the following points. First, when the hydraulic cylinder is loaded and then the actuating speed reaches a certain standard, Harbin Hydraulic equipment Hydraulic cylinder with buffer device must be used. Or when the speed reaches a higher speed, a deceleration valve must be installed outside the hydraulic cylinder; Secondly, carefully select hydraulic oil and oil seal. Oil seals of different materials are selected for different hydraulic oils, Harbin Hydraulic equipment Price To ensure the service life of the hydraulic cylinder.

Select the cylinder type correctly according to the working requirements and conditions. It is required that there is no impact phenomenon and impact noise when the cylinder reaches the end of the stroke; Cushion cylinder shall be selected; Light weight is required; It is required to select light cylinder; Harbin Hydraulic equipment Narrow installation space and short stroke are required; It is required to select thin cylinder; It is required to have transverse load, and the cylinder with guide rod can be selected; High braking accuracy is required, and locking cylinder can be selected; It is not allowed to rotate the piston rod, and the cylinder with rod non rotation function can be selected; Harbin Hydraulic equipment Price In corrosive environment, corrosion-resistant steel cylinders shall be selected.

If the piston rod of the hydraulic cylinder is not treated in time after being pulled, the normal use will be affected if it is light, and the operation will not be possible if it is heavy. The repair methods we adopt are local polishing to repair light draw marks, welding and manual polishing to repair heavy draw marks. Harbin Hydraulic equipment Through quenching and tempering treatment, the comprehensive mechanical properties of the cylinder piston rod with good strength and toughness matching were obtained. Harbin Hydraulic equipment Price The purpose of surface hardening is to obtain high surface hardness to support the chromium plating layer on the surface, so as to improve the wear resistance and corrosion resistance of the piston rod.

How to install and fix the hydraulic cylinder? There are two common ways to fix the hydraulic cylinder: the first is the square hydraulic cylinder fixed on the B plate, and the hydraulic cylinder needs to be positioned on the B plate. The second is a round hydraulic cylinder fixed on the ejector plate. It should be noted that the thimble plate locking screw needs to be added next to the hydraulic cylinder, and the force at this position is large, Harbin Hydraulic equipment Prevent tension deformation. Another point is to inscribe words on the hydraulic cylinder, and write down the stroke of the hydraulic cylinder for easy verification. To correctly install the sealing device at each position of the hydraulic cylinder: Harbin Hydraulic equipment Price When installing the O-ring seal, pay attention to its installation direction to avoid oil leakage due to installation. Its lip should face the oil chamber with pressure.

Hydraulic oil cylinder is used in many industries. Once it fails, it will have a far-reaching impact and hinder the progress of all work. In fact, many customers said that the hydraulic cylinder could not operate, Harbin Hydraulic equipment In order to solve this problem in time, we should first find out what causes the problem. Generally speaking, the problem that the hydraulic cylinder cannot act often occurs on the newly installed hydraulic cylinder, Harbin Hydraulic equipment Price Generally, it is necessary to start from external reasons, such as whether the mechanism pulled by the hydraulic cylinder has excessive resistance, whether it is stuck, and whether it is against other parts; Whether the pressure at the oil inlet of the hydraulic cylinder is within the specified range.