How to install and fix the hydraulic cylinder? There are two common ways to fix the hydraulic cylinder: the first is the square hydraulic cylinder fixed on the B plate, and the hydraulic cylinder needs to be positioned on the B plate. The second is a round hydraulic cylinder fixed on the ejector plate. It should be noted that the thimble plate locking screw needs to be added next to the hydraulic cylinder, and the force at this position is large, Heilongjiang Hydraulic system Prevent tension deformation. Another point is to inscribe words on the hydraulic cylinder, and write down the stroke of the hydraulic cylinder for easy verification. To correctly install the sealing device at each position of the hydraulic cylinder: Heilongjiang Hydraulic system manufactor When installing the O-ring seal, pay attention to its installation direction to avoid oil leakage due to installation. Its lip should face the oil chamber with pressure.
The hydraulic system is composed of various hydraulic components. All hydraulic components are organically connected into a complete hydraulic system by pipes, joints, integrated valve blocks and other parts. Therefore, whether the hydraulic pipeline is installed correctly Heilongjiang Hydraulic system Firm, reliable and neat will have an important impact on the working performance of the hydraulic system. Check the quality of pipes. Find out the pipe material Heilongjiang Hydraulic system manufactor Whether the size and quality meet the design requirements; Check whether there is serious flattening or bending on the appearance of the pipe, whether there is corrosion on the surface of the inner and outer walls of the pipe, whether there is crack on the outer wall and other defects.
1、 If the groove is too deep, two situations will occur: A. If the gap between the seal root and the groove becomes larger, the seal root will become unstable. B. The interference between the sealing lip and the sealing surface becomes smaller, Heilongjiang Hydraulic system The rebound force of the seal becomes smaller, and the failure rate of low-pressure oil leakage will increase when the piston rod jumps. 2、 If the groove is too shallow, two situations will also occur: A. The interference between the sealing lip and the sealing surface will increase, and the contact area will increase, which will lead to greater friction, Heilongjiang Hydraulic system manufactor The increased heat accelerates the damage of the seal lip. B. As a result, the clearance at the seal root becomes smaller, and the probability of the seal root being squeezed out when the oil cylinder is under high pressure increases.
It is suitable for hydraulic transmission of construction machinery, lifting, transportation machinery and mining machinery. Hydraulic transmission principle - oil is used as working medium, Heilongjiang Hydraulic system The movement is transmitted through the change of sealing volume, and the power is transmitted through the pressure inside the oil. 1. Power part - converts mechanical energy of prime mover into pressure energy (hydraulic energy) of oil. For example: hydraulic pump. 2. Executive part - converts the oil pressure energy input by the hydraulic pump into the mechanical energy driving the working mechanism. For example: hydraulic cylinder, hydraulic motor. 3. Control part - used to control and adjust the oil pressure Heilongjiang Hydraulic system manufactor Flow rate and flow direction. For example: pressure control valve, flow control valve.
The diameter of the oil unloading hole of the hydraulic cylinder is too large, which directly affects the service life of the rubber seal ring on the piston. Because the piston moves back and forth, Heilongjiang Hydraulic system When the rubber seal ring on the piston passes through the oil discharge hole, the rubber's own elasticity expands to the oil discharge hole, and the oil discharge hole edge and the piston seal groove edge shear the rubber seal ring. At the same time, China has the advantages of strong market demand and low cost, and is expected to become the center of gravity of the world's hydraulic industry and oil cylinder industry in the future. The hydraulic cylinder is a very important part of the hydraulic machinery and plays an executive role in the entire hydraulic machinery, Heilongjiang Hydraulic system manufactor In the whole process, the hydraulic cylinder converts hydraulic energy into mechanical energy.
Hydraulic oil cylinder is used in many industries. Once it fails, it will have a far-reaching impact and hinder the progress of all work. In fact, many customers said that the hydraulic cylinder could not operate, Heilongjiang Hydraulic system In order to solve this problem in time, we should first find out what causes the problem. Generally speaking, the problem that the hydraulic cylinder cannot act often occurs on the newly installed hydraulic cylinder, Heilongjiang Hydraulic system manufactor Generally, it is necessary to start from external reasons, such as whether the mechanism pulled by the hydraulic cylinder has excessive resistance, whether it is stuck, and whether it is against other parts; Whether the pressure at the oil inlet of the hydraulic cylinder is within the specified range.
