上海新茶外卖高端

 Hydraulic cylinder manufacturer
Your current location: home page > Hot information

contact us Contact Us

Foshan Fuchao Hydraulic Electromechanical Equipment Co., Ltd

Mobile: 15975751599

Mobile: 13531395368

Tel.: 0757-85131606

Email: [email protected]

Website: uonetech.com.cn

Address: No. 26 and 27, Road 9, Zone 2, Xiedei Bridge, Guidan Avenue, Xiebian Second Industrial Zone, Dali Town, Nanhai District, Foshan City

Wuhan customized hydraulic press cylinder manufacturer

2021-08-07
 Wuhan customized hydraulic press cylinder manufacturer

The two lips of the seal have two contact circumferential surfaces. Whether the force on the inner and outer circumferences is evenly distributed means that the force on the two circumferences cannot be zero. If the force on a certain point is zero, the shaft seal has inner and outer lips, Wuhan Hydraulic press cylinder The outer lip is installed in the groove to contact the outer wall, and the inner lip is in contact with the piston rod surface. Both lips have an interference amount, which is equal to the generation of two contact circumferential surfaces, that is, the generation of two circumferential rebound forces. How to determine the magnitude of the circumferential force? Both the inner and outer lips of the seal have two chamfers. Since the interference of the same inner and outer lips is certain, Wuhan Hydraulic press cylinder Manufacturer The angle of the chamfer determines the size of the circumferential area of the inner and outer contact of the two lips.

 Wuhan customized hydraulic press cylinder manufacturer

If the piston rod of the hydraulic cylinder is not treated in time after being pulled, the normal use will be affected if it is light, and the operation will not be possible if it is heavy. The repair methods we adopt are local polishing to repair light draw marks, welding and manual polishing to repair heavy draw marks. Wuhan Hydraulic press cylinder Through quenching and tempering treatment, the comprehensive mechanical properties of the cylinder piston rod with good strength and toughness matching were obtained. Wuhan Hydraulic press cylinder Manufacturer The purpose of surface hardening is to obtain high surface hardness to support the chromium plating layer on the surface, so as to improve the wear resistance and corrosion resistance of the piston rod.

 Wuhan customized hydraulic press cylinder manufacturer

The oil cylinder shall be assembled in a special workshop or assembly area, and the temperature shall be kept at 20~250C, Wuhan Hydraulic press cylinder Manufacturer It shall be far away from the tuyere, dust and cutting area, with fresh air, no dust and no noise; Avoid direct glare. The assembly room shall be equipped with installation platform, sufficient working position apparatus, assembly turnover vehicle Wuhan Hydraulic press cylinder Lifting and hoisting equipment and the following special basic equipment. a: Cylinder loader; b: Another cylinder cleaning machine is used to heat and clean another part; c: Pressure test equipment, used for pressure test of oil cylinder; d: The air duct is used to clean and dry the other parts after cleaning.

 Wuhan customized hydraulic press cylinder manufacturer

The connection between the oil cylinder and the actuator and the connection between the oil cylinder and the oil pipe cannot be the same, because there must be some differences between the connection between the oil cylinder and different products. In addition, during the use of the oil cylinder, it is necessary to avoid scratches, Wuhan Hydraulic press cylinder Because if this problem occurs, it will affect the normal use of the oil cylinder. At present, there is no software for designing hydraulic cylinders, but there are design standards for hydraulic cylinders, and it is necessary to design hydraulic cylinders according to these standards. So far, Wuhan Hydraulic press cylinder Manufacturer There is no software for designing hydraulic cylinders, but there are design standards for hydraulic cylinders.

home page             About us             Product display             Success stories             after-sale service             News Center             contact us

contact information           Site Map           Online Message

Tel: 15975751599/13531395368

Service hotline: 0757-85131606

Email: [email protected]

Address: No. 26 and 27, Road 9, Zone 2, Xiedei Bridge, Guidan Avenue, Xiebian Second Industrial Zone, Dali Town, Nanhai District, Foshan City

 Oil cylinder manufacturer

Service, service, heat and line

159-7575-1599

135-3139-5368

Copyright © Foshan Fuchao Hydraulic Electromechanical Equipment Co., Ltd. All rights reserved is mainly engaged in Oil cylinder manufacturer , Hydraulic cylinder manufacturer , Oil cylinder manufacturer Welcome to inquire!
Record No.: Service support: Statement: Part of the content and pictures of this site are from the Internet. If there is infringement, please contact the administrator to delete it at the first time. Thank you!
Main business area: Foshan Shenzhen Guangzhou Zhongshan Guangdong Zhuhai Dongguan Huizhou Guangxi Beijing