For the selection of hydraulic cylinder, the hydraulic cylinder will be selected according to the inner diameter, stroke, operating pressure and installation type during the selection of hydraulic cylinder. In fact, in addition to these, we should pay attention to the following points. First, when the hydraulic cylinder is loaded and then the actuating speed reaches a certain standard, Jiangmen Hydraulic cylinder Hydraulic cylinder with buffer device must be used. Or when the speed reaches a higher speed, a deceleration valve must be installed outside the hydraulic cylinder; Secondly, carefully select hydraulic oil and oil seal. Oil seals of different materials are selected for different hydraulic oils, Jiangmen Hydraulic cylinder Manufacturer To ensure the service life of the hydraulic cylinder.
It is suitable for hydraulic transmission of construction machinery, lifting, transportation machinery and mining machinery. Hydraulic transmission principle - oil is used as working medium, Jiangmen Hydraulic cylinder The movement is transmitted through the change of sealing volume, and the power is transmitted through the pressure inside the oil. 1. Power part - converts mechanical energy of prime mover into pressure energy (hydraulic energy) of oil. For example: hydraulic pump. 2. Executive part - converts the oil pressure energy input by the hydraulic pump into the mechanical energy driving the working mechanism. For example: hydraulic cylinder, hydraulic motor. 3. Control part - used to control and adjust the oil pressure Jiangmen Hydraulic cylinder Manufacturer Flow rate and flow direction. For example: pressure control valve, flow control valve.
Items to be checked when the speed of hydraulic cylinder slows down. 1. Where and what type of oil cylinder has been used for several years, Jiangmen Hydraulic cylinder What is the working pressure. You don't have any of these. How can I troubleshoot them for you. Check the lower seal if there is internal leakage. 2. It is likely that the internal working pressure of the oil cylinder has decreased. 3. Check whether the system is blocked, Jiangmen Hydraulic cylinder Manufacturer In addition, check whether the oil cylinder seal ring is damaged, and then check whether the piston rod is damaged. Basically, these aspects can identify the problem.
The oil cylinder shall be assembled in a special workshop or assembly area, and the temperature shall be kept at 20~250C, Jiangmen Hydraulic cylinder Manufacturer It shall be far away from the tuyere, dust and cutting area, with fresh air, no dust and no noise; Avoid direct glare. The assembly room shall be equipped with installation platform, sufficient working position apparatus, assembly turnover vehicle Jiangmen Hydraulic cylinder Lifting and hoisting equipment and the following special basic equipment. a: Cylinder loader; b: Another cylinder cleaning machine is used to heat and clean another part; c: Pressure test equipment, used for pressure test of oil cylinder; d: The air duct is used to clean and dry the other parts after cleaning.
The hydraulic cylinder is the actuating element that converts hydraulic energy into mechanical energy in the hydraulic system. The faults can be basically summarized as hydraulic cylinder misoperation Jiangmen Hydraulic cylinder Manufacturer It is unable to push the load and the piston slips or crawls. It is not uncommon for hydraulic cylinder failure to cause equipment shutdown. Therefore, Jiangmen Hydraulic cylinder Attention should be paid to the fault diagnosis, use and maintenance of hydraulic cylinder. The main reason for excessive wear of piston seals is that the speed control valve is improperly adjusted, resulting in excessive back pressure, improper installation of seals or contamination of hydraulic oil. Secondly, foreign matters enter during assembly and the quality of sealing materials is poor.
The diameter of the oil unloading hole of the hydraulic cylinder is too large, which directly affects the service life of the rubber seal ring on the piston. Because the piston moves back and forth, Jiangmen Hydraulic cylinder When the rubber seal ring on the piston passes through the oil discharge hole, the rubber's own elasticity expands to the oil discharge hole, and the oil discharge hole edge and the piston seal groove edge shear the rubber seal ring. At the same time, China has the advantages of strong market demand and low cost, and is expected to become the center of gravity of the world's hydraulic industry and oil cylinder industry in the future. The hydraulic cylinder is a very important part of the hydraulic machinery and plays an executive role in the entire hydraulic machinery, Jiangmen Hydraulic cylinder Manufacturer In the whole process, the hydraulic cylinder converts hydraulic energy into mechanical energy.
