上海新茶外卖高端

 Hydraulic cylinder manufacturer
Your current location: home page > Hot information

contact us Contact Us

Foshan Fuchao Hydraulic Electromechanical Equipment Co., Ltd

Mobile: 15975751599

Mobile: 13531395368

Tel.: 0757-85131606

Email: [email protected]

Website: uonetech.com.cn

Address: No. 26 and 27, Road 9, Zone 2, Xiedei Bridge, Guidan Avenue, Xiebian Second Industrial Zone, Dali Town, Nanhai District, Foshan City

Suzhou hydraulic press cylinder manufacturer

2021-07-17
 Suzhou hydraulic press cylinder manufacturer

If the piston rod of the hydraulic cylinder is not treated in time after being pulled, the normal use will be affected if it is light, and the operation will not be possible if it is heavy. The repair methods we adopt are local polishing to repair light draw marks, welding and manual polishing to repair heavy draw marks. Suzhou Hydraulic press cylinder Through quenching and tempering treatment, the comprehensive mechanical properties of the cylinder piston rod with good strength and toughness matching were obtained. Suzhou Hydraulic press cylinder manufactor The purpose of surface hardening is to obtain high surface hardness to support the chromium plating layer on the surface, so as to improve the wear resistance and corrosion resistance of the piston rod.

 Suzhou hydraulic press cylinder manufacturer

Because the hydraulic cylinder has to bear a great pressure, the heavier the load, the greater its pressure will be. Therefore, the maintenance of the hydraulic cylinder is an important part of the maintenance of the entire hydraulic system. The hydraulic cylinder is the heart of the hydraulic system, Suzhou Hydraulic press cylinder It is difficult to repair the heart problem, so the maintenance of the hydraulic cylinder should be careful. First, rust prevention. Because the piston part of the hydraulic cylinder will extend the cylinder in the working state, Suzhou Hydraulic press cylinder manufactor Naturally, it will be corroded by oxide and acid gas, which requires us to coat it with proper grease for protection.

 Suzhou hydraulic press cylinder manufacturer

Two way hydraulic cylinder, which is one of the hydraulic cylinders, is a common and commonly used type of hydraulic cylinder. Therefore, Suzhou Hydraulic press cylinder manufactor It is necessary to have a correct understanding of this kind of hydraulic cylinder and have a certain understanding, so that we can know how to use it reasonably and make full use of it. This kind of hydraulic cylinder has corresponding operation regulations and maintenance regulations, because it is in the hydraulic cylinder category. In addition, Suzhou Hydraulic press cylinder It is necessary to have a clear and comprehensive understanding of its operation and maintenance procedures. The symptom of strain and wear is that the lifting speed of the equipment is relatively slow, accompanied by self subsidence.

 Suzhou hydraulic press cylinder manufacturer

For the selection of hydraulic cylinder, the hydraulic cylinder will be selected according to the inner diameter, stroke, operating pressure and installation type during the selection of hydraulic cylinder. In fact, in addition to these, we should pay attention to the following points. First, when the hydraulic cylinder is loaded and then the actuating speed reaches a certain standard, Suzhou Hydraulic press cylinder Hydraulic cylinder with buffer device must be used. Or when the speed reaches a higher speed, a deceleration valve must be installed outside the hydraulic cylinder; Secondly, carefully select hydraulic oil and oil seal. Oil seals of different materials are selected for different hydraulic oils, Suzhou Hydraulic press cylinder manufactor To ensure the service life of the hydraulic cylinder.

home page             About us             Product display             Success stories             after-sale service             News Center             contact us

contact information           Site Map           Online Message

Tel: 15975751599/13531395368

Service hotline: 0757-85131606

Email: [email protected]

Address: No. 26 and 27, Road 9, Zone 2, Xiedei Bridge, Guidan Avenue, Xiebian Second Industrial Zone, Dali Town, Nanhai District, Foshan City

 Oil cylinder manufacturer

Service, service, heat and line

159-7575-1599

135-3139-5368

Copyright © Foshan Fuchao Hydraulic Electromechanical Equipment Co., Ltd. All rights reserved is mainly engaged in Oil cylinder manufacturer , Hydraulic cylinder manufacturer , Oil cylinder manufacturer Welcome to inquire!
Record No.: Service support: Statement: Part of the content and pictures of this site are from the Internet. If there is infringement, please contact the administrator to delete it at the first time. Thank you!
Main business area: Foshan Shenzhen Guangzhou Zhongshan Guangdong Zhuhai Dongguan Huizhou Guangxi Beijing