The connection between the oil cylinder and the actuator and the connection between the oil cylinder and the oil pipe cannot be the same, because there must be some differences between the connection between the oil cylinder and different products. In addition, during the use of the oil cylinder, it is necessary to avoid scratches, Handan Hydraulic cylinder Because if this problem occurs, it will affect the normal use of the oil cylinder. At present, there is no software for designing hydraulic cylinders, but there are design standards for hydraulic cylinders, and it is necessary to design hydraulic cylinders according to these standards. So far, Handan Hydraulic cylinder Manufacturer There is no software for designing hydraulic cylinders, but there are design standards for hydraulic cylinders.

The hydraulic cylinder is the actuating element that converts hydraulic energy into mechanical energy in the hydraulic system. The faults can be basically summarized as hydraulic cylinder misoperation Handan Hydraulic cylinder Manufacturer It is unable to push the load and the piston slips or crawls. It is not uncommon for hydraulic cylinder failure to cause equipment shutdown. Therefore, Handan Hydraulic cylinder Attention should be paid to the fault diagnosis, use and maintenance of hydraulic cylinder. The main reason for excessive wear of piston seals is that the speed control valve is improperly adjusted, resulting in excessive back pressure, improper installation of seals or contamination of hydraulic oil. Secondly, foreign matters enter during assembly and the quality of sealing materials is poor.

For the selection of hydraulic cylinder, the hydraulic cylinder will be selected according to the inner diameter, stroke, operating pressure and installation type during the selection of hydraulic cylinder. In fact, in addition to these, we should pay attention to the following points. First, when the hydraulic cylinder is loaded and then the actuating speed reaches a certain standard, Handan Hydraulic cylinder Hydraulic cylinder with buffer device must be used. Or when the speed reaches a higher speed, a deceleration valve must be installed outside the hydraulic cylinder; Secondly, carefully select hydraulic oil and oil seal. Oil seals of different materials are selected for different hydraulic oils, Handan Hydraulic cylinder Manufacturer To ensure the service life of the hydraulic cylinder.

The speed ratio refers to the same flow (volume of liquid entering the hydraulic cylinder per unit time), Handan Hydraulic cylinder Manufacturer The ratio of the piston rod extension speed to the retraction speed. The calculation is equal to the inverse ratio of the large cavity area and the small cavity area of the cylinder. The speed ratio is related to the cylinder diameter and rod diameter of the oil cylinder. Main products: harvesting machinery series Handan Hydraulic cylinder Flip plow series, press series, grader series, TGL, HG, SG, DG series vehicle oil cylinder, HSG series engineering oil cylinder mining machinery, ship oil cylinder, and various non-standard oil cylinders. Welcome to order!

Two way hydraulic cylinder, which is one of the hydraulic cylinders, is a common and commonly used type of hydraulic cylinder. Therefore, Handan Hydraulic cylinder Manufacturer It is necessary to have a correct understanding of this kind of hydraulic cylinder and have a certain understanding, so that we can know how to use it reasonably and make full use of it. This kind of hydraulic cylinder has corresponding operation regulations and maintenance regulations, because it is in the hydraulic cylinder category. In addition, Handan Hydraulic cylinder It is necessary to have a clear and comprehensive understanding of its operation and maintenance procedures. The symptom of strain and wear is that the lifting speed of the equipment is relatively slow, accompanied by self subsidence.

How to install and fix the hydraulic cylinder? There are two common ways to fix the hydraulic cylinder: the first is the square hydraulic cylinder fixed on the B plate, and the hydraulic cylinder needs to be positioned on the B plate. The second is a round hydraulic cylinder fixed on the ejector plate. It should be noted that the thimble plate locking screw needs to be added next to the hydraulic cylinder, and the force at this position is large, Handan Hydraulic cylinder Prevent tension deformation. Another point is to inscribe words on the hydraulic cylinder, and write down the stroke of the hydraulic cylinder for easy verification. To correctly install the sealing device at each position of the hydraulic cylinder: Handan Hydraulic cylinder Manufacturer When installing the O-ring seal, pay attention to its installation direction to avoid oil leakage due to installation. Its lip should face the oil chamber with pressure.