1、 If the groove is too deep, two situations will occur: A. If the gap between the seal root and the groove becomes larger, the seal root will become unstable. B. The interference between the sealing lip and the sealing surface becomes smaller, Liaoyuan Hydraulic cylinder The rebound force of the seal becomes smaller, and the failure rate of low-pressure oil leakage will increase when the piston rod jumps. 2、 If the groove is too shallow, two situations will also occur: A. The interference between the sealing lip and the sealing surface will increase, and the contact area will increase, which will lead to greater friction, Liaoyuan Hydraulic cylinder Price The increased heat accelerates the damage of the seal lip. B. As a result, the clearance at the seal root becomes smaller, and the probability of the seal root being squeezed out when the oil cylinder is under high pressure increases.

The connection between the oil cylinder and the actuator and the connection between the oil cylinder and the oil pipe cannot be the same, because there must be some differences between the connection between the oil cylinder and different products. In addition, during the use of the oil cylinder, it is necessary to avoid scratches, Liaoyuan Hydraulic cylinder Because if this problem occurs, it will affect the normal use of the oil cylinder. At present, there is no software for designing hydraulic cylinders, but there are design standards for hydraulic cylinders, and it is necessary to design hydraulic cylinders according to these standards. So far, Liaoyuan Hydraulic cylinder Price There is no software for designing hydraulic cylinders, but there are design standards for hydraulic cylinders.

The valve core of the flow valve in the hydraulic cylinder is blocked, which is easy to cause the action failure of the hydraulic cylinder. We need to check whether there are pollutants in the oil in the hydraulic cylinder and whether the valve body is worn. It is necessary to check whether the piston rod seal is too tight, Liaoyuan Hydraulic cylinder Whether there are pollutants entering, whether the axis line is aligned, and whether the easily damaged components fail. If the pressure controlled by the hydraulic system is too low, the action of the hydraulic cylinder will also fail, Liaoyuan Hydraulic cylinder Price At this time, it is necessary to check the control pressure source to ensure that the pressure value is consistent with the specified value of the system.

Two way hydraulic cylinder, which is one of the hydraulic cylinders, is a common and commonly used type of hydraulic cylinder. Therefore, Liaoyuan Hydraulic cylinder Price It is necessary to have a correct understanding of this kind of hydraulic cylinder and have a certain understanding, so that we can know how to use it reasonably and make full use of it. This kind of hydraulic cylinder has corresponding operation regulations and maintenance regulations, because it is in the hydraulic cylinder category. In addition, Liaoyuan Hydraulic cylinder It is necessary to have a clear and comprehensive understanding of its operation and maintenance procedures. The symptom of strain and wear is that the lifting speed of the equipment is relatively slow, accompanied by self subsidence.

The two lips of the seal have two contact circumferential surfaces. Whether the force on the inner and outer circumferences is evenly distributed means that the force on the two circumferences cannot be zero. If the force on a certain point is zero, the shaft seal has inner and outer lips, Liaoyuan Hydraulic cylinder The outer lip is installed in the groove to contact the outer wall, and the inner lip is in contact with the piston rod surface. Both lips have an interference amount, which is equal to the generation of two contact circumferential surfaces, that is, the generation of two circumferential rebound forces. How to determine the magnitude of the circumferential force? Both the inner and outer lips of the seal have two chamfers. Since the interference of the same inner and outer lips is certain, Liaoyuan Hydraulic cylinder Price The angle of the chamfer determines the size of the circumferential area of the inner and outer contact of the two lips.

The hydraulic cylinder is the actuating element that converts hydraulic energy into mechanical energy in the hydraulic system. The faults can be basically summarized as hydraulic cylinder misoperation Liaoyuan Hydraulic cylinder Price It is unable to push the load and the piston slips or crawls. It is not uncommon for hydraulic cylinder failure to cause equipment shutdown. Therefore, Liaoyuan Hydraulic cylinder Attention should be paid to the fault diagnosis, use and maintenance of hydraulic cylinder. The main reason for excessive wear of piston seals is that the speed control valve is improperly adjusted, resulting in excessive back pressure, improper installation of seals or contamination of hydraulic oil. Secondly, foreign matters enter during assembly and the quality of sealing materials is poor.