Before removing the hydraulic cylinder, depressurize the hydraulic circuit. Otherwise, when the oil pipe joint connected with the oil cylinder is loosened, Shenzhen Hydraulic equipment The high-pressure oil in the circuit will be ejected rapidly. When the hydraulic circuit is depressurized, first loosen the hand wheel or pressure regulating screw at the overflow valve to unload the pressure oil, and then cut off the power supply or power source to stop the hydraulic device. During unloading, prevent damage to the thread at the top of the piston rod, the thread at the oil port, the surface of the piston rod, the inner wall of the cylinder liner, etc. Shenzhen Hydraulic equipment manufactor In order to prevent the piston rod and other slender parts from bending or deformation, the skid shall be used to support and balance during placement.
The oil cylinder shall be assembled in a special workshop or assembly area, and the temperature shall be kept at 20~250C, Shenzhen Hydraulic equipment manufactor It shall be far away from the tuyere, dust and cutting area, with fresh air, no dust and no noise; Avoid direct glare. The assembly room shall be equipped with installation platform, sufficient working position apparatus, assembly turnover vehicle Shenzhen Hydraulic equipment Lifting and hoisting equipment and the following special basic equipment. a: Cylinder loader; b: Another cylinder cleaning machine is used to heat and clean another part; c: Pressure test equipment, used for pressure test of oil cylinder; d: The air duct is used to clean and dry the other parts after cleaning.
Select the cylinder type correctly according to the working requirements and conditions. It is required that there is no impact phenomenon and impact noise when the cylinder reaches the end of the stroke; Cushion cylinder shall be selected; Light weight is required; It is required to select light cylinder; Shenzhen Hydraulic equipment Narrow installation space and short stroke are required; It is required to select thin cylinder; It is required to have transverse load, and the cylinder with guide rod can be selected; High braking accuracy is required, and locking cylinder can be selected; It is not allowed to rotate the piston rod, and the cylinder with rod non rotation function can be selected; Shenzhen Hydraulic equipment manufactor In corrosive environment, corrosion-resistant steel cylinders shall be selected.
Hydraulic cylinder is a hydraulic actuator that converts hydraulic energy into mechanical energy and performs linear reciprocating motion (or swing motion). It is simple in structure and reliable in operation. When it is used to realize reciprocating movement, the reducer can be avoided, Shenzhen Hydraulic equipment And there is no transmission clearance, smooth movement, so it is widely used in various mechanical hydraulic systems. Output force of the hydraulic cylinder is proportional to effective area of the piston and pressure difference on both sides; The hydraulic cylinder basically consists of cylinder barrel, cylinder head Shenzhen Hydraulic equipment manufactor The piston and piston rod, sealing device, buffer device and exhaust device are composed.
1. There are many factors that cause this problem. First, measure the pressure of the main system to see whether the pressure of the main system in the pressure holding state is consistent with the initial setting. Check the hydraulic oil and suction oil filter before measuring the pressure, Shenzhen Hydraulic equipment Replace or clean it. Secondly, check the main overflow valve of the reversing control multi way valve to see if it is damaged or blocked by foreign matters, Shenzhen Hydraulic equipment manufactor Clean it. If your pump is a gear pump, the problem should be minor in general. 2. Next, let's look at the traffic problem.
As the structure and size of various hydraulic cylinders are different, the disassembly sequence is slightly different. Generally, drain the oil in the two chambers of the oil cylinder, remove the cylinder head, and finally remove the piston and piston rod. Shenzhen Hydraulic equipment When disassembling the cylinder head of the hydraulic cylinder, special tools shall be used for the key or snap ring of the internal key type connection, and flat shovel is prohibited; Flange end caps must be pushed out with screws, and hammering or hard prying is not allowed. When it is difficult to draw out the piston and piston rod, do not force them out, Shenzhen Hydraulic equipment manufactor The reason shall be found out before disassembly. Before and after unloading, try to create conditions to prevent the parts of the hydraulic cylinder from being polluted by the surrounding dust and impurities.
