Items to be checked when the speed of hydraulic cylinder slows down. 1. Where and what type of oil cylinder has been used for several years, Jiangmen Hydraulic cylinder What is the working pressure. You don't have any of these. How can I troubleshoot them for you. Check the lower seal if there is internal leakage. 2. It is likely that the internal working pressure of the oil cylinder has decreased. 3. Check whether the system is blocked, Jiangmen Hydraulic cylinder Price In addition, check whether the oil cylinder seal ring is damaged, and then check whether the piston rod is damaged. Basically, these aspects can identify the problem.

For the selection of hydraulic cylinder, the hydraulic cylinder will be selected according to the inner diameter, stroke, operating pressure and installation type during the selection of hydraulic cylinder. In fact, in addition to these, we should pay attention to the following points. First, when the hydraulic cylinder is loaded and then the actuating speed reaches a certain standard, Jiangmen Hydraulic cylinder Hydraulic cylinder with buffer device must be used. Or when the speed reaches a higher speed, a deceleration valve must be installed outside the hydraulic cylinder; Secondly, carefully select hydraulic oil and oil seal. Oil seals of different materials are selected for different hydraulic oils, Jiangmen Hydraulic cylinder Price To ensure the service life of the hydraulic cylinder.

Fluid cleanliness. The cleanliness of the system oil will have a very important impact on the hydraulic cylinder. Hydraulic shock and vibration hydraulic cylinders will be affected by the performance of components, pipeline and medium characteristics, etc., which will be accompanied by hydraulic shock and vibration. Generally speaking, if the oil temperature is too high or too low, Jiangmen Hydraulic cylinder Price Will have a great impact on the working efficiency of the hydraulic cylinder. If the oil temperature of the hydraulic cylinder is too high or too low, the physical and chemical properties of the medium will change, Jiangmen Hydraulic cylinder As a result, the viscosity of the working medium decreases or the possibility of leakage increases.

It is suitable for hydraulic transmission of construction machinery, lifting, transportation machinery and mining machinery. Hydraulic transmission principle - oil is used as working medium, Jiangmen Hydraulic cylinder The movement is transmitted through the change of sealing volume, and the power is transmitted through the pressure inside the oil. 1. Power part - converts mechanical energy of prime mover into pressure energy (hydraulic energy) of oil. For example: hydraulic pump. 2. Executive part - converts the oil pressure energy input by the hydraulic pump into the mechanical energy driving the working mechanism. For example: hydraulic cylinder, hydraulic motor. 3. Control part - used to control and adjust the oil pressure Jiangmen Hydraulic cylinder Price Flow rate and flow direction. For example: pressure control valve, flow control valve.

Before removing the hydraulic cylinder, depressurize the hydraulic circuit. Otherwise, when the oil pipe joint connected with the oil cylinder is loosened, Jiangmen Hydraulic cylinder The high-pressure oil in the circuit will be ejected rapidly. When the hydraulic circuit is depressurized, first loosen the hand wheel or pressure regulating screw at the overflow valve to unload the pressure oil, and then cut off the power supply or power source to stop the hydraulic device. During unloading, prevent damage to the thread at the top of the piston rod, the thread at the oil port, the surface of the piston rod, the inner wall of the cylinder liner, etc. Jiangmen Hydraulic cylinder Price In order to prevent the piston rod and other slender parts from bending or deformation, the skid shall be used to support and balance during placement.

1、 If the groove is too deep, two situations will occur: A. If the gap between the seal root and the groove becomes larger, the seal root will become unstable. B. The interference between the sealing lip and the sealing surface becomes smaller, Jiangmen Hydraulic cylinder The rebound force of the seal becomes smaller, and the failure rate of low-pressure oil leakage will increase when the piston rod jumps. 2、 If the groove is too shallow, two situations will also occur: A. The interference between the sealing lip and the sealing surface will increase, and the contact area will increase, which will lead to greater friction, Jiangmen Hydraulic cylinder Price The increased heat accelerates the damage of the seal lip. B. As a result, the clearance at the seal root becomes smaller, and the probability of the seal root being squeezed out when the oil cylinder is under high pressure increases.