As the structure and size of various hydraulic cylinders are different, the disassembly sequence is slightly different. Generally, drain the oil in the two chambers of the oil cylinder, remove the cylinder head, and finally remove the piston and piston rod. Guilin Hydraulic cylinder When disassembling the cylinder head of the hydraulic cylinder, special tools shall be used for the key or snap ring of the internal key type connection, and flat shovel is prohibited; Flange end caps must be pushed out with screws, and hammering or hard prying is not allowed. When it is difficult to draw out the piston and piston rod, do not force them out, Guilin Hydraulic cylinder manufactor The reason shall be found out before disassembly. Before and after unloading, try to create conditions to prevent the parts of the hydraulic cylinder from being polluted by the surrounding dust and impurities.

The hydraulic system is composed of various hydraulic components. All hydraulic components are organically connected into a complete hydraulic system by pipes, joints, integrated valve blocks and other parts. Therefore, whether the hydraulic pipeline is installed correctly Guilin Hydraulic cylinder Firm, reliable and neat will have an important impact on the working performance of the hydraulic system. Check the quality of pipes. Find out the pipe material Guilin Hydraulic cylinder manufactor Whether the size and quality meet the design requirements; Check whether there is serious flattening or bending on the appearance of the pipe, whether there is corrosion on the surface of the inner and outer walls of the pipe, whether there is crack on the outer wall and other defects.

How to install and fix the hydraulic cylinder? There are two common ways to fix the hydraulic cylinder: the first is the square hydraulic cylinder fixed on the B plate, and the hydraulic cylinder needs to be positioned on the B plate. The second is a round hydraulic cylinder fixed on the ejector plate. It should be noted that the thimble plate locking screw needs to be added next to the hydraulic cylinder, and the force at this position is large, Guilin Hydraulic cylinder Prevent tension deformation. Another point is to inscribe words on the hydraulic cylinder, and write down the stroke of the hydraulic cylinder for easy verification. To correctly install the sealing device at each position of the hydraulic cylinder: Guilin Hydraulic cylinder manufactor When installing the O-ring seal, pay attention to its installation direction to avoid oil leakage due to installation. Its lip should face the oil chamber with pressure.

Hydraulic oil cylinder is used in many industries. Once it fails, it will have a far-reaching impact and hinder the progress of all work. In fact, many customers said that the hydraulic cylinder could not operate, Guilin Hydraulic cylinder In order to solve this problem in time, we should first find out what causes the problem. Generally speaking, the problem that the hydraulic cylinder cannot act often occurs on the newly installed hydraulic cylinder, Guilin Hydraulic cylinder manufactor Generally, it is necessary to start from external reasons, such as whether the mechanism pulled by the hydraulic cylinder has excessive resistance, whether it is stuck, and whether it is against other parts; Whether the pressure at the oil inlet of the hydraulic cylinder is within the specified range.

Because the hydraulic cylinder must bear a great pressure, the heavier the load, the greater its pressure will be. Therefore, the maintenance of the hydraulic cylinder is the most important part of the maintenance of the entire hydraulic system. The hydraulic cylinder is the heart of the hydraulic system. It is difficult to repair a heart problem, so the maintenance of the hydraulic cylinder should be careful. first, Guilin Hydraulic cylinder Rust prevention is required. Because the piston part of the hydraulic cylinder will extend out of the cylinder in the working state, it will naturally suffer from oxidation Guilin Hydraulic cylinder manufactor The erosion of acid gas requires us to apply proper amount of grease to protect it.

The two lips of the seal have two contact circumferential surfaces. Whether the force on the inner and outer circumferences is evenly distributed means that the force on the two circumferences cannot be zero. If the force on a certain point is zero, the shaft seal has inner and outer lips, Guilin Hydraulic cylinder The outer lip is installed in the groove to contact the outer wall, and the inner lip is in contact with the piston rod surface. Both lips have an interference amount, which is equal to the generation of two contact circumferential surfaces, that is, the generation of two circumferential rebound forces. How to determine the magnitude of the circumferential force? Both the inner and outer lips of the seal have two chamfers. Since the interference of the same inner and outer lips is certain, Guilin Hydraulic cylinder manufactor The angle of the chamfer determines the size of the circumferential area of the inner and outer contact of the two lips.