1. There are many factors that cause this problem. First, measure the pressure of the main system to see whether the pressure of the main system in the pressure holding state is consistent with the initial setting. Check the hydraulic oil and suction oil filter before measuring the pressure, Fujian Hydraulic press cylinder Replace or clean it. Secondly, check the main overflow valve of the reversing control multi way valve to see if it is damaged or blocked by foreign matters, Fujian Hydraulic press cylinder manufactor Clean it. If your pump is a gear pump, the problem should be minor in general. 2. Next, let's look at the traffic problem.
1、 If the groove is too deep, two situations will occur: A. If the gap between the seal root and the groove becomes larger, the seal root will become unstable. B. The interference between the sealing lip and the sealing surface becomes smaller, Fujian Hydraulic press cylinder The rebound force of the seal becomes smaller, and the failure rate of low-pressure oil leakage will increase when the piston rod jumps. 2、 If the groove is too shallow, two situations will also occur: A. The interference between the sealing lip and the sealing surface will increase, and the contact area will increase, which will lead to greater friction, Fujian Hydraulic press cylinder manufactor The increased heat accelerates the damage of the seal lip. B. As a result, the clearance at the seal root becomes smaller, and the probability of the seal root being squeezed out when the oil cylinder is under high pressure increases.
The diameter of the oil unloading hole of the hydraulic cylinder is too large, which directly affects the service life of the rubber seal ring on the piston. Because the piston moves back and forth, Fujian Hydraulic press cylinder When the rubber seal ring on the piston passes through the oil discharge hole, the rubber's own elasticity expands to the oil discharge hole, and the oil discharge hole edge and the piston seal groove edge shear the rubber seal ring. At the same time, China has the advantages of strong market demand and low cost, and is expected to become the center of gravity of the world's hydraulic industry and oil cylinder industry in the future. The hydraulic cylinder is a very important part of the hydraulic machinery and plays an executive role in the entire hydraulic machinery, Fujian Hydraulic press cylinder manufactor In the whole process, the hydraulic cylinder converts hydraulic energy into mechanical energy.
Before removing the hydraulic cylinder, depressurize the hydraulic circuit. Otherwise, when the oil pipe joint connected with the oil cylinder is loosened, Fujian Hydraulic press cylinder The high-pressure oil in the circuit will be ejected rapidly. When the hydraulic circuit is depressurized, first loosen the hand wheel or pressure regulating screw at the overflow valve to unload the pressure oil, and then cut off the power supply or power source to stop the hydraulic device. During unloading, prevent damage to the thread at the top of the piston rod, the thread at the oil port, the surface of the piston rod, the inner wall of the cylinder liner, etc. Fujian Hydraulic press cylinder manufactor In order to prevent the piston rod and other slender parts from bending or deformation, the skid shall be used to support and balance during placement.
As the structure and size of various hydraulic cylinders are different, the disassembly sequence is slightly different. Generally, drain the oil in the two chambers of the oil cylinder, remove the cylinder head, and finally remove the piston and piston rod. Fujian Hydraulic press cylinder When disassembling the cylinder head of the hydraulic cylinder, special tools shall be used for the key or snap ring of the internal key type connection, and flat shovel is prohibited; Flange end caps must be pushed out with screws, and hammering or hard prying is not allowed. When it is difficult to draw out the piston and piston rod, do not force them out, Fujian Hydraulic press cylinder manufactor The reason shall be found out before disassembly. Before and after unloading, try to create conditions to prevent the parts of the hydraulic cylinder from being polluted by the surrounding dust and impurities.
Fluid cleanliness. The cleanliness of the system oil will have a very important impact on the hydraulic cylinder. Hydraulic shock and vibration hydraulic cylinders will be affected by the performance of components, pipeline and medium characteristics, etc., which will be accompanied by hydraulic shock and vibration. Generally speaking, if the oil temperature is too high or too low, Fujian Hydraulic press cylinder manufactor Will have a great impact on the working efficiency of the hydraulic cylinder. If the oil temperature of the hydraulic cylinder is too high or too low, the physical and chemical properties of the medium will change, Fujian Hydraulic press cylinder As a result, the viscosity of the working medium decreases or the possibility of leakage increases.
