Fluid cleanliness. The cleanliness of the system oil will have a very important impact on the hydraulic cylinder. Hydraulic shock and vibration hydraulic cylinders will be affected by the performance of components, pipeline and medium characteristics, etc., which will be accompanied by hydraulic shock and vibration. Generally speaking, if the oil temperature is too high or too low, Kunming Cylinder Manufacturer Will have a great impact on the working efficiency of the hydraulic cylinder. If the oil temperature of the hydraulic cylinder is too high or too low, the physical and chemical properties of the medium will change, Kunming Cylinder As a result, the viscosity of the working medium decreases or the possibility of leakage increases.

As the structure and size of various hydraulic cylinders are different, the disassembly sequence is slightly different. Generally, drain the oil in the two chambers of the oil cylinder, remove the cylinder head, and finally remove the piston and piston rod. Kunming Cylinder When disassembling the cylinder head of the hydraulic cylinder, special tools shall be used for the key or snap ring of the internal key type connection, and flat shovel is prohibited; Flange end caps must be pushed out with screws, and hammering or hard prying is not allowed. When it is difficult to draw out the piston and piston rod, do not force them out, Kunming Cylinder Manufacturer The reason shall be found out before disassembly. Before and after unloading, try to create conditions to prevent the parts of the hydraulic cylinder from being polluted by the surrounding dust and impurities.

1、 If the groove is too deep, two situations will occur: A. If the gap between the seal root and the groove becomes larger, the seal root will become unstable. B. The interference between the sealing lip and the sealing surface becomes smaller, Kunming Cylinder The rebound force of the seal becomes smaller, and the failure rate of low-pressure oil leakage will increase when the piston rod jumps. 2、 If the groove is too shallow, two situations will also occur: A. The interference between the sealing lip and the sealing surface will increase, and the contact area will increase, which will lead to greater friction, Kunming Cylinder Manufacturer The increased heat accelerates the damage of the seal lip. B. As a result, the clearance at the seal root becomes smaller, and the probability of the seal root being squeezed out when the oil cylinder is under high pressure increases.

Select the cylinder type correctly according to the working requirements and conditions. It is required that there is no impact phenomenon and impact noise when the cylinder reaches the end of the stroke; Cushion cylinder shall be selected; Light weight is required; It is required to select light cylinder; Kunming Cylinder Narrow installation space and short stroke are required; It is required to select thin cylinder; It is required to have transverse load, and the cylinder with guide rod can be selected; High braking accuracy is required, and locking cylinder can be selected; It is not allowed to rotate the piston rod, and the cylinder with rod non rotation function can be selected; Kunming Cylinder Manufacturer In corrosive environment, corrosion-resistant steel cylinders shall be selected.

Two way hydraulic cylinder, which is one of the hydraulic cylinders, is a common and commonly used type of hydraulic cylinder. Therefore, Kunming Cylinder Manufacturer It is necessary to have a correct understanding of this kind of hydraulic cylinder and have a certain understanding, so that we can know how to use it reasonably and make full use of it. This kind of hydraulic cylinder has corresponding operation regulations and maintenance regulations, because it is in the hydraulic cylinder category. In addition, Kunming Cylinder It is necessary to have a clear and comprehensive understanding of its operation and maintenance procedures. The symptom of strain and wear is that the lifting speed of the equipment is relatively slow, accompanied by self subsidence.

There are many hydraulic components on construction machinery, and sufficient hydraulic oil is required. When the hydraulic oil needs to be replaced due to its deterioration after a long time of use, some people mistakenly believe that only drain the oil in the hydraulic cylinder and fill it with new hydraulic oil. However, there are still many old hydraulic oils left in the hydraulic oil pipe and hydraulic control valve, Kunming Cylinder When the equipment is used, the mixing of new and old oil will speed up the deterioration of new oil. The correct oil change procedure should first drain the hydraulic oil in the hydraulic cylinder, Kunming Cylinder Manufacturer After cleaning the hydraulic cylinder, add new hydraulic oil, remove the circuit header, start the engine and run at low speed to make the oil pump work.