How to install and fix the hydraulic cylinder? There are two common ways to fix the hydraulic cylinder: the first is the square hydraulic cylinder fixed on the B plate, and the hydraulic cylinder needs to be positioned on the B plate. The second is a round hydraulic cylinder fixed on the ejector plate. It should be noted that the thimble plate locking screw needs to be added next to the hydraulic cylinder, and the force at this position is large, Nanjing Hydraulic cylinder Prevent tension deformation. Another point is to inscribe words on the hydraulic cylinder, and write down the stroke of the hydraulic cylinder for easy verification. To correctly install the sealing device at each position of the hydraulic cylinder: Nanjing Hydraulic cylinder manufactor When installing the O-ring seal, pay attention to its installation direction to avoid oil leakage due to installation. Its lip should face the oil chamber with pressure.

The speed ratio refers to the same flow (volume of liquid entering the hydraulic cylinder per unit time), Nanjing Hydraulic cylinder manufactor The ratio of the piston rod extension speed to the retraction speed. The calculation is equal to the inverse ratio of the large cavity area and the small cavity area of the cylinder. The speed ratio is related to the cylinder diameter and rod diameter of the oil cylinder. Main products: harvesting machinery series Nanjing Hydraulic cylinder Flip plow series, press series, grader series, TGL, HG, SG, DG series vehicle oil cylinder, HSG series engineering oil cylinder mining machinery, ship oil cylinder, and various non-standard oil cylinders. Welcome to order!

1、 If the groove is too deep, two situations will occur: A. If the gap between the seal root and the groove becomes larger, the seal root will become unstable. B. The interference between the sealing lip and the sealing surface becomes smaller, Nanjing Hydraulic cylinder The rebound force of the seal becomes smaller, and the failure rate of low-pressure oil leakage will increase when the piston rod jumps. 2、 If the groove is too shallow, two situations will also occur: A. The interference between the sealing lip and the sealing surface will increase, and the contact area will increase, which will lead to greater friction, Nanjing Hydraulic cylinder manufactor The increased heat accelerates the damage of the seal lip. B. As a result, the clearance at the seal root becomes smaller, and the probability of the seal root being squeezed out when the oil cylinder is under high pressure increases.

It is suitable for hydraulic transmission of construction machinery, lifting, transportation machinery and mining machinery. Hydraulic transmission principle - oil is used as working medium, Nanjing Hydraulic cylinder The movement is transmitted through the change of sealing volume, and the power is transmitted through the pressure inside the oil. 1. Power part - converts mechanical energy of prime mover into pressure energy (hydraulic energy) of oil. For example: hydraulic pump. 2. Executive part - converts the oil pressure energy input by the hydraulic pump into the mechanical energy driving the working mechanism. For example: hydraulic cylinder, hydraulic motor. 3. Control part - used to control and adjust the oil pressure Nanjing Hydraulic cylinder manufactor Flow rate and flow direction. For example: pressure control valve, flow control valve.

There are many hydraulic components on construction machinery, and sufficient hydraulic oil is required. When the hydraulic oil needs to be replaced due to its deterioration after a long time of use, some people mistakenly believe that only drain the oil in the hydraulic cylinder and fill it with new hydraulic oil. However, there are still many old hydraulic oils left in the hydraulic oil pipe and hydraulic control valve, Nanjing Hydraulic cylinder When the equipment is used, the mixing of new and old oil will speed up the deterioration of new oil. The correct oil change procedure should first drain the hydraulic oil in the hydraulic cylinder, Nanjing Hydraulic cylinder manufactor After cleaning the hydraulic cylinder, add new hydraulic oil, remove the circuit header, start the engine and run at low speed to make the oil pump work.

For the same hydraulic cylinder on the Internet, some manufacturers quote more than 1200, some more than 1600, some about 1800, and even some about 3000. This situation makes the purchasing manufacturers feel puzzled and very difficult. Most manufacturers have limited procurement funds, Nanjing Hydraulic cylinder Therefore, if you want to achieve the predetermined purchase goal, you need to choose the hydraulic cylinder with high cost performance ratio, good quality and low price. However, the price gap of hydraulic cylinders in the market is staggering, Nanjing Hydraulic cylinder manufactor If you choose cheap oil cylinder rashly, the quality cannot be guaranteed, which will lead to endless troubles.