Because the hydraulic cylinder has to bear a great pressure, the heavier the load, the greater its pressure will be. Therefore, the maintenance of the hydraulic cylinder is an important part of the maintenance of the entire hydraulic system. The hydraulic cylinder is the heart of the hydraulic system, Taiyuan Cylinder It is difficult to repair the heart problem, so the maintenance of the hydraulic cylinder should be careful. First, rust prevention. Because the piston part of the hydraulic cylinder will extend the cylinder in the working state, Taiyuan Cylinder Manufacturer Naturally, it will be corroded by oxide and acid gas, which requires us to coat it with proper grease for protection.

The two lips of the seal have two contact circumferential surfaces. Whether the force on the inner and outer circumferences is evenly distributed means that the force on the two circumferences cannot be zero. If the force on a certain point is zero, the shaft seal has inner and outer lips, Taiyuan Cylinder The outer lip is installed in the groove to contact the outer wall, and the inner lip is in contact with the piston rod surface. Both lips have an interference amount, which is equal to the generation of two contact circumferential surfaces, that is, the generation of two circumferential rebound forces. How to determine the magnitude of the circumferential force? Both the inner and outer lips of the seal have two chamfers. Since the interference of the same inner and outer lips is certain, Taiyuan Cylinder Manufacturer The angle of the chamfer determines the size of the circumferential area of the inner and outer contact of the two lips.

For the selection of hydraulic cylinder, the hydraulic cylinder will be selected according to the inner diameter, stroke, operating pressure and installation type during the selection of hydraulic cylinder. In fact, in addition to these, we should pay attention to the following points. First, when the hydraulic cylinder is loaded and then the actuating speed reaches a certain standard, Taiyuan Cylinder Hydraulic cylinder with buffer device must be used. Or when the speed reaches a higher speed, a deceleration valve must be installed outside the hydraulic cylinder; Secondly, carefully select hydraulic oil and oil seal. Oil seals of different materials are selected for different hydraulic oils, Taiyuan Cylinder Manufacturer To ensure the service life of the hydraulic cylinder.

Hydraulic cylinder is a hydraulic actuator that converts hydraulic energy into mechanical energy and performs linear reciprocating motion (or swing motion). It is simple in structure and reliable in operation. When it is used to realize reciprocating movement, the reducer can be avoided, Taiyuan Cylinder And there is no transmission clearance, smooth movement, so it is widely used in various mechanical hydraulic systems. Output force of the hydraulic cylinder is proportional to effective area of the piston and pressure difference on both sides; The hydraulic cylinder basically consists of cylinder barrel, cylinder head Taiyuan Cylinder Manufacturer The piston and piston rod, sealing device, buffer device and exhaust device are composed.

There are many hydraulic components on construction machinery, and sufficient hydraulic oil is required. When the hydraulic oil needs to be replaced due to its deterioration after a long time of use, some people mistakenly believe that it is only necessary to drain the oil in the hydraulic cylinder Taiyuan Cylinder Top up with new hydraulic oil. However, there are still many old hydraulic oils left in the hydraulic oil pipe and hydraulic control valve at this time. When the equipment is used, the mixing of new and old oils will speed up the deterioration of new oils. The correct oil change procedure should first drain the hydraulic oil in the hydraulic cylinder, clean the hydraulic cylinder, and then add new hydraulic oil, Taiyuan Cylinder Manufacturer Then remove the circuit header, start the engine and run at low speed to make the oil pump work and operate each mechanism separately.

Select the cylinder type correctly according to the working requirements and conditions. It is required that there is no impact phenomenon and impact noise when the cylinder reaches the end of the stroke; Cushion cylinder shall be selected; Light weight is required; It is required to select light cylinder; Taiyuan Cylinder Narrow installation space and short stroke are required; It is required to select thin cylinder; It is required to have transverse load, and the cylinder with guide rod can be selected; High braking accuracy is required, and locking cylinder can be selected; It is not allowed to rotate the piston rod, and the cylinder with rod non rotation function can be selected; Taiyuan Cylinder Manufacturer In corrosive environment, corrosion-resistant steel cylinders shall be selected.