Two way hydraulic cylinder, which is one of the hydraulic cylinders, is a common and commonly used type of hydraulic cylinder. Therefore, Fujian Hydraulic equipment Manufacturer It is necessary to have a correct understanding of this kind of hydraulic cylinder and have a certain understanding, so that we can know how to use it reasonably and make full use of it. This kind of hydraulic cylinder has corresponding operation regulations and maintenance regulations, because it is in the hydraulic cylinder category. In addition, Fujian Hydraulic equipment It is necessary to have a clear and comprehensive understanding of its operation and maintenance procedures. The symptom of strain and wear is that the lifting speed of the equipment is relatively slow, accompanied by self subsidence.

As the structure and size of various hydraulic cylinders are different, the disassembly sequence is slightly different. Generally, drain the oil in the two chambers of the oil cylinder, remove the cylinder head, and finally remove the piston and piston rod. Fujian Hydraulic equipment When disassembling the cylinder head of the hydraulic cylinder, special tools shall be used for the key or snap ring of the internal key type connection, and flat shovel is prohibited; Flange end caps must be pushed out with screws, and hammering or hard prying is not allowed. When it is difficult to draw out the piston and piston rod, do not force them out, Fujian Hydraulic equipment Manufacturer The reason shall be found out before disassembly. Before and after unloading, try to create conditions to prevent the parts of the hydraulic cylinder from being polluted by the surrounding dust and impurities.

It is suitable for hydraulic transmission of construction machinery, lifting, transportation machinery and mining machinery. Hydraulic transmission principle - oil is used as working medium, Fujian Hydraulic equipment The movement is transmitted through the change of sealing volume, and the power is transmitted through the pressure inside the oil. 1. Power part - converts mechanical energy of prime mover into pressure energy (hydraulic energy) of oil. For example: hydraulic pump. 2. Executive part - converts the oil pressure energy input by the hydraulic pump into the mechanical energy driving the working mechanism. For example: hydraulic cylinder, hydraulic motor. 3. Control part - used to control and adjust the oil pressure Fujian Hydraulic equipment Manufacturer Flow rate and flow direction. For example: pressure control valve, flow control valve.

The oil cylinder shall be assembled in a special workshop or assembly area, and the temperature shall be kept at 20~250C, Fujian Hydraulic equipment Manufacturer It shall be far away from the tuyere, dust and cutting area, with fresh air, no dust and no noise; Avoid direct glare. The assembly room shall be equipped with installation platform, sufficient working position apparatus, assembly turnover vehicle Fujian Hydraulic equipment Lifting and hoisting equipment and the following special basic equipment. a: Cylinder loader; b: Another cylinder cleaning machine is used to heat and clean another part; c: Pressure test equipment, used for pressure test of oil cylinder; d: The air duct is used to clean and dry the other parts after cleaning.

The hydraulic system is composed of various hydraulic components. All hydraulic components are organically connected into a complete hydraulic system by pipes, joints, integrated valve blocks and other parts. Therefore, whether the hydraulic pipeline is installed correctly Fujian Hydraulic equipment Firm, reliable and neat will have an important impact on the working performance of the hydraulic system. Check the quality of pipes. Find out the pipe material Fujian Hydraulic equipment Manufacturer Whether the size and quality meet the design requirements; Check whether there is serious flattening or bending on the appearance of the pipe, whether there is corrosion on the surface of the inner and outer walls of the pipe, whether there is crack on the outer wall and other defects.

The hydraulic cylinder is the actuating element that converts hydraulic energy into mechanical energy in the hydraulic system. The faults can be basically summarized as hydraulic cylinder misoperation Fujian Hydraulic equipment Manufacturer It is unable to push the load and the piston slips or crawls. It is not uncommon for hydraulic cylinder failure to cause equipment shutdown. Therefore, Fujian Hydraulic equipment Attention should be paid to the fault diagnosis, use and maintenance of hydraulic cylinder. The main reason for excessive wear of piston seals is that the speed control valve is improperly adjusted, resulting in excessive back pressure, improper installation of seals or contamination of hydraulic oil. Secondly, foreign matters enter during assembly and the quality of sealing materials is poor.