上海新茶外卖高端

 Hydraulic cylinder manufacturer
Your current location: home page > Hot information

contact us Contact Us

Foshan Fuchao Hydraulic Electromechanical Equipment Co., Ltd

Mobile: 15975751599

Mobile: 13531395368

Tel.: 0757-85131606

Email: [email protected]

Website: uonetech.com.cn

Address: No. 26 and 27, Road 9, Zone 2, Xiedei Bridge, Guidan Avenue, Xiebian Second Industrial Zone, Dali Town, Nanhai District, Foshan City

Liuzhou professional hydraulic cylinder manufacturer

2021-02-16
 Liuzhou professional hydraulic cylinder manufacturer

The diameter of the oil unloading hole of the hydraulic cylinder is too large, which directly affects the service life of the rubber seal ring on the piston. Because the piston moves back and forth, city in Guangxi Hydraulic cylinder When the rubber seal ring on the piston passes through the oil discharge hole, the rubber's own elasticity expands to the oil discharge hole, and the oil discharge hole edge and the piston seal groove edge shear the rubber seal ring. At the same time, China has the advantages of strong market demand and low cost, and is expected to become the center of gravity of the world's hydraulic industry and oil cylinder industry in the future. The hydraulic cylinder is a very important part of the hydraulic machinery and plays an executive role in the entire hydraulic machinery, city in Guangxi Hydraulic cylinder Manufacturer In the whole process, the hydraulic cylinder converts hydraulic energy into mechanical energy.

 Liuzhou professional hydraulic cylinder manufacturer

For the selection of hydraulic cylinder, the hydraulic cylinder will be selected according to the inner diameter, stroke, operating pressure and installation type during the selection of hydraulic cylinder. In fact, in addition to these, we should pay attention to the following points. First, when the hydraulic cylinder is loaded and then the actuating speed reaches a certain standard, city in Guangxi Hydraulic cylinder Hydraulic cylinder with buffer device must be used. Or when the speed reaches a higher speed, a deceleration valve must be installed outside the hydraulic cylinder; Secondly, carefully select hydraulic oil and oil seal. Oil seals of different materials are selected for different hydraulic oils, city in Guangxi Hydraulic cylinder Manufacturer To ensure the service life of the hydraulic cylinder.

 Liuzhou professional hydraulic cylinder manufacturer

There are many hydraulic components on construction machinery, and sufficient hydraulic oil is required. When the hydraulic oil needs to be replaced due to its deterioration after a long time of use, some people mistakenly believe that only drain the oil in the hydraulic cylinder and fill it with new hydraulic oil. However, there are still many old hydraulic oils left in the hydraulic oil pipe and hydraulic control valve, city in Guangxi Hydraulic cylinder When the equipment is used, the mixing of new and old oil will speed up the deterioration of new oil. The correct oil change procedure should first drain the hydraulic oil in the hydraulic cylinder, city in Guangxi Hydraulic cylinder Manufacturer After cleaning the hydraulic cylinder, add new hydraulic oil, remove the circuit header, start the engine and run at low speed to make the oil pump work.

 Liuzhou professional hydraulic cylinder manufacturer

Hydraulic oil cylinder is used in many industries. Once it fails, it will have a far-reaching impact and hinder the progress of all work. In fact, many customers said that the hydraulic cylinder could not operate, city in Guangxi Hydraulic cylinder In order to solve this problem in time, we should first find out what causes the problem. Generally speaking, the problem that the hydraulic cylinder cannot act often occurs on the newly installed hydraulic cylinder, city in Guangxi Hydraulic cylinder Manufacturer Generally, it is necessary to start from external reasons, such as whether the mechanism pulled by the hydraulic cylinder has excessive resistance, whether it is stuck, and whether it is against other parts; Whether the pressure at the oil inlet of the hydraulic cylinder is within the specified range.

 Liuzhou professional hydraulic cylinder manufacturer

Because the hydraulic cylinder has to bear a great pressure, the heavier the load, the greater its pressure will be. Therefore, the maintenance of the hydraulic cylinder is an important part of the maintenance of the entire hydraulic system. The hydraulic cylinder is the heart of the hydraulic system, city in Guangxi Hydraulic cylinder It is difficult to repair the heart problem, so the maintenance of the hydraulic cylinder should be careful. First, rust prevention. Because the piston part of the hydraulic cylinder will extend the cylinder in the working state, city in Guangxi Hydraulic cylinder Manufacturer Naturally, it will be corroded by oxide and acid gas, which requires us to coat it with proper grease for protection.

 Liuzhou professional hydraulic cylinder manufacturer

Before removing the hydraulic cylinder, depressurize the hydraulic circuit. Otherwise, when the oil pipe joint connected with the oil cylinder is loosened, city in Guangxi Hydraulic cylinder The high-pressure oil in the circuit will be ejected rapidly. When the hydraulic circuit is depressurized, first loosen the hand wheel or pressure regulating screw at the overflow valve to unload the pressure oil, and then cut off the power supply or power source to stop the hydraulic device. During unloading, prevent damage to the thread at the top of the piston rod, the thread at the oil port, the surface of the piston rod, the inner wall of the cylinder liner, etc. city in Guangxi Hydraulic cylinder Manufacturer In order to prevent the piston rod and other slender parts from bending or deformation, the skid shall be used to support and balance during placement.

home page             About us             Product display             Success stories             after-sale service             News Center             contact us

contact information           Site Map           Online Message

Tel: 15975751599/13531395368

Service hotline: 0757-85131606

Email: [email protected]

Address: No. 26 and 27, Road 9, Zone 2, Xiedei Bridge, Guidan Avenue, Xiebian Second Industrial Zone, Dali Town, Nanhai District, Foshan City

 Oil cylinder manufacturer

Service, service, heat and line

159-7575-1599

135-3139-5368

Copyright © Foshan Fuchao Hydraulic Electromechanical Equipment Co., Ltd. All rights reserved is mainly engaged in Oil cylinder manufacturer , Hydraulic cylinder manufacturer , Oil cylinder manufacturer Welcome to inquire!
Record No.: Service support: Statement: Part of the content and pictures of this site are from the Internet. If there is infringement, please contact the administrator to delete it at the first time. Thank you!
Main business area: Foshan Shenzhen Guangzhou Zhongshan Guangdong Zhuhai Dongguan Huizhou Guangxi Beijing