The two lips of the seal have two contact circumferential surfaces. Whether the force on the inner and outer circumferences is evenly distributed means that the force on the two circumferences cannot be zero. If the force on a certain point is zero, the shaft seal has inner and outer lips, Chongqing Hydraulic system The outer lip is installed in the groove to contact the outer wall, and the inner lip is in contact with the piston rod surface. Both lips have an interference amount, which is equal to the generation of two contact circumferential surfaces, that is, the generation of two circumferential rebound forces. How to determine the magnitude of the circumferential force? Both the inner and outer lips of the seal have two chamfers. Since the interference of the same inner and outer lips is certain, Chongqing Hydraulic system Manufacturer The angle of the chamfer determines the size of the circumferential area of the inner and outer contact of the two lips.
The failure of the hydraulic cylinder due to improper design and manufacture is because the oil pressure cannot act on the effective working area of the piston when the piston travels to the end point and returns, or the effective working area is too small when starting, which causes problems. When the transverse load of the hydraulic cylinder is too large, the force is not strong or the cylinder is bitten, the same consequences will occur. Chongqing Hydraulic system Therefore, when installing the hydraulic cylinder, the axis position of the cylinder must be consistent with the movement direction; Chongqing Hydraulic system Manufacturer And ensure that the load borne by the hydraulic cylinder passes through the cylinder axis as far as possible without eccentricity, so that the problem can be solved.
1. Internal leakage of oil cylinder; 2. Internal leakage at control valve hole and valve rod; 3. Overload overflow valve is poor; 4. The valve rod is not in the middle position; 5. PPC valve is not in the middle position. Hydraulic cylinder maintenance process: 1. Whether the hydraulic lock becomes normal when it is in the determined position, if so, check the PPC valve first; 2. Conduct oil cylinder plugging oil port test, Chongqing Hydraulic system Check whether the oil cylinder is defective, and repair the oil cylinder if it is; 3. Replace the overload overflow valve and check whether it is the fault of the overload overflow valve; 4. Whether the valve rod is jammed, Chongqing Hydraulic system Manufacturer Check again after cleaning, otherwise the main control valve needs to be repaired.
The valve core of the flow valve in the hydraulic cylinder is blocked, which is easy to cause the action failure of the hydraulic cylinder. We need to check whether there are pollutants in the oil in the hydraulic cylinder and whether the valve body is worn. It is necessary to check whether the piston rod seal is too tight, Chongqing Hydraulic system Whether there are pollutants entering, whether the axis line is aligned, and whether the easily damaged components fail. If the pressure controlled by the hydraulic system is too low, the action of the hydraulic cylinder will also fail, Chongqing Hydraulic system Manufacturer At this time, it is necessary to check the control pressure source to ensure that the pressure value is consistent with the specified value of the system.
The oil cylinder shall be assembled in a special workshop or assembly area, and the temperature shall be kept at 20~250C, Chongqing Hydraulic system Manufacturer It shall be far away from the tuyere, dust and cutting area, with fresh air, no dust and no noise; Avoid direct glare. The assembly room shall be equipped with installation platform, sufficient working position apparatus, assembly turnover vehicle Chongqing Hydraulic system Lifting and hoisting equipment and the following special basic equipment. a: Cylinder loader; b: Another cylinder cleaning machine is used to heat and clean another part; c: Pressure test equipment, used for pressure test of oil cylinder; d: The air duct is used to clean and dry the other parts after cleaning.
For the same hydraulic cylinder on the Internet, some manufacturers quote more than 1200, some more than 1600, some about 1800, and even some about 3000. This situation makes the purchasing manufacturers feel puzzled and very difficult. Most manufacturers have limited procurement funds, Chongqing Hydraulic system Therefore, if you want to achieve the predetermined purchase goal, you need to choose the hydraulic cylinder with high cost performance ratio, good quality and low price. However, the price gap of hydraulic cylinders in the market is staggering, Chongqing Hydraulic system Manufacturer If you choose cheap oil cylinder rashly, the quality cannot be guaranteed, which will lead to endless troubles.
