1、 If the groove is too deep, two situations will occur: A. If the gap between the seal root and the groove becomes larger, the seal root will become unstable. B. The interference between the sealing lip and the sealing surface becomes smaller, Cangzhou Hydraulic machinery The rebound force of the seal becomes smaller, and the failure rate of low-pressure oil leakage will increase when the piston rod jumps. 2、 If the groove is too shallow, two situations will also occur: A. The interference between the sealing lip and the sealing surface will increase, and the contact area will increase, which will lead to greater friction, Cangzhou Hydraulic machinery Price The increased heat accelerates the damage of the seal lip. B. As a result, the clearance at the seal root becomes smaller, and the probability of the seal root being squeezed out when the oil cylinder is under high pressure increases.
There are many hydraulic components on construction machinery, and sufficient hydraulic oil is required. When the hydraulic oil needs to be replaced due to its deterioration after a long time of use, some people mistakenly believe that it is only necessary to drain the oil in the hydraulic cylinder Cangzhou Hydraulic machinery Top up with new hydraulic oil. However, there are still many old hydraulic oils left in the hydraulic oil pipe and hydraulic control valve at this time. When the equipment is used, the mixing of new and old oils will speed up the deterioration of new oils. The correct oil change procedure should first drain the hydraulic oil in the hydraulic cylinder, clean the hydraulic cylinder, and then add new hydraulic oil, Cangzhou Hydraulic machinery Price Then remove the circuit header, start the engine and run at low speed to make the oil pump work and operate each mechanism separately.
It is suitable for hydraulic transmission of construction machinery, lifting, transportation machinery and mining machinery. Hydraulic transmission principle - oil is used as working medium, Cangzhou Hydraulic machinery The movement is transmitted through the change of sealing volume, and the power is transmitted through the pressure inside the oil. 1. Power part - converts mechanical energy of prime mover into pressure energy (hydraulic energy) of oil. For example: hydraulic pump. 2. Executive part - converts the oil pressure energy input by the hydraulic pump into the mechanical energy driving the working mechanism. For example: hydraulic cylinder, hydraulic motor. 3. Control part - used to control and adjust the oil pressure Cangzhou Hydraulic machinery Price Flow rate and flow direction. For example: pressure control valve, flow control valve.
The connection between the oil cylinder and the actuator and the connection between the oil cylinder and the oil pipe cannot be the same, because there must be some differences between the connection between the oil cylinder and different products. In addition, during the use of the oil cylinder, it is necessary to avoid scratches, Cangzhou Hydraulic machinery Because if this problem occurs, it will affect the normal use of the oil cylinder. At present, there is no software for designing hydraulic cylinders, but there are design standards for hydraulic cylinders, and it is necessary to design hydraulic cylinders according to these standards. So far, Cangzhou Hydraulic machinery Price There is no software for designing hydraulic cylinders, but there are design standards for hydraulic cylinders.
Fluid cleanliness. The cleanliness of the system oil will have a very important impact on the hydraulic cylinder. Hydraulic shock and vibration hydraulic cylinders will be affected by the performance of components, pipeline and medium characteristics, etc., which will be accompanied by hydraulic shock and vibration. Generally speaking, if the oil temperature is too high or too low, Cangzhou Hydraulic machinery Price Will have a great impact on the working efficiency of the hydraulic cylinder. If the oil temperature of the hydraulic cylinder is too high or too low, the physical and chemical properties of the medium will change, Cangzhou Hydraulic machinery As a result, the viscosity of the working medium decreases or the possibility of leakage increases.
1. There are many factors that cause this problem. First, measure the pressure of the main system to see whether the pressure of the main system in the pressure holding state is consistent with the initial setting. Check the hydraulic oil and suction oil filter before measuring the pressure, Cangzhou Hydraulic machinery Replace or clean it. Secondly, check the main overflow valve of the reversing control multi way valve to see if it is damaged or blocked by foreign matters, Cangzhou Hydraulic machinery Price Clean it. If your pump is a gear pump, the problem should be minor in general. 2. Next, let's look at the traffic problem.
