Select the cylinder type correctly according to the working requirements and conditions. It is required that there is no impact phenomenon and impact noise when the cylinder reaches the end of the stroke; Cushion cylinder shall be selected; Light weight is required; It is required to select light cylinder; Wuhan Hydraulic equipment Narrow installation space and short stroke are required; It is required to select thin cylinder; It is required to have transverse load, and the cylinder with guide rod can be selected; High braking accuracy is required, and locking cylinder can be selected; It is not allowed to rotate the piston rod, and the cylinder with rod non rotation function can be selected; Wuhan Hydraulic equipment Price In corrosive environment, corrosion-resistant steel cylinders shall be selected.
The diameter of the oil unloading hole of the hydraulic cylinder is too large, which directly affects the service life of the rubber seal ring on the piston. Because the piston moves back and forth, Wuhan Hydraulic equipment When the rubber seal ring on the piston passes through the oil discharge hole, the rubber's own elasticity expands to the oil discharge hole, and the oil discharge hole edge and the piston seal groove edge shear the rubber seal ring. At the same time, China has the advantages of strong market demand and low cost, and is expected to become the center of gravity of the world's hydraulic industry and oil cylinder industry in the future. The hydraulic cylinder is a very important part of the hydraulic machinery and plays an executive role in the entire hydraulic machinery, Wuhan Hydraulic equipment Price In the whole process, the hydraulic cylinder converts hydraulic energy into mechanical energy.
Hydraulic cylinder is a hydraulic actuator that converts hydraulic energy into mechanical energy and performs linear reciprocating motion (or swing motion). It is simple in structure and reliable in operation. When it is used to realize reciprocating movement, the reducer can be avoided, Wuhan Hydraulic equipment And there is no transmission clearance, smooth movement, so it is widely used in various mechanical hydraulic systems. Output force of the hydraulic cylinder is proportional to effective area of the piston and pressure difference on both sides; The hydraulic cylinder basically consists of cylinder barrel, cylinder head Wuhan Hydraulic equipment Price The piston and piston rod, sealing device, buffer device and exhaust device are composed.
1、 If the groove is too deep, two situations will occur: A. If the gap between the seal root and the groove becomes larger, the seal root will become unstable. B. The interference between the sealing lip and the sealing surface becomes smaller, Wuhan Hydraulic equipment The rebound force of the seal becomes smaller, and the failure rate of low-pressure oil leakage will increase when the piston rod jumps. 2、 If the groove is too shallow, two situations will also occur: A. The interference between the sealing lip and the sealing surface will increase, and the contact area will increase, which will lead to greater friction, Wuhan Hydraulic equipment Price The increased heat accelerates the damage of the seal lip. B. As a result, the clearance at the seal root becomes smaller, and the probability of the seal root being squeezed out when the oil cylinder is under high pressure increases.
As the structure and size of various hydraulic cylinders are different, the disassembly sequence is slightly different. Generally, drain the oil in the two chambers of the oil cylinder, remove the cylinder head, and finally remove the piston and piston rod. Wuhan Hydraulic equipment When disassembling the cylinder head of the hydraulic cylinder, special tools shall be used for the key or snap ring of the internal key type connection, and flat shovel is prohibited; Flange end caps must be pushed out with screws, and hammering or hard prying is not allowed. When it is difficult to draw out the piston and piston rod, do not force them out, Wuhan Hydraulic equipment Price The reason shall be found out before disassembly. Before and after unloading, try to create conditions to prevent the parts of the hydraulic cylinder from being polluted by the surrounding dust and impurities.
1. Internal leakage of oil cylinder; 2. Internal leakage at control valve hole and valve rod; 3. Overload overflow valve is poor; 4. The valve rod is not in the middle position; 5. PPC valve is not in the middle position. Hydraulic cylinder maintenance process: 1. Whether the hydraulic lock becomes normal when it is in the determined position, if so, check the PPC valve first; 2. Conduct oil cylinder plugging oil port test, Wuhan Hydraulic equipment Check whether the oil cylinder is defective, and repair the oil cylinder if it is; 3. Replace the overload overflow valve and check whether it is the fault of the overload overflow valve; 4. Whether the valve rod is jammed, Wuhan Hydraulic equipment Price Check again after cleaning, otherwise the main control valve needs to be repaired.
