1、 If the groove is too deep, two situations will occur: A. If the gap between the seal root and the groove becomes larger, the seal root will become unstable. B、 The interference between the sealing lip and the sealing surface becomes smaller, Inner Mongolia Cylinder The rebound force of the seal becomes smaller, and the failure rate of low-pressure oil leakage will increase when the piston rod jumps. 2、 If the groove is too shallow, two situations will also occur: A. The interference between the sealing lip and the sealing surface will increase, and the contact area will increase, which will lead to greater friction, Inner Mongolia Cylinder Price The increased heat accelerates the damage of the seal lip. B、 As a result, the clearance at the seal root becomes smaller, and the probability of the seal root being squeezed out when the oil cylinder is under high pressure increases.

Hydraulic cylinder is a hydraulic actuator that converts hydraulic energy into mechanical energy and performs linear reciprocating motion (or swing motion). It is simple in structure and reliable in operation. When it is used to realize reciprocating movement, the reducer can be avoided, Inner Mongolia Cylinder And there is no transmission clearance, smooth movement, so it is widely used in various mechanical hydraulic systems. Output force of the hydraulic cylinder is proportional to effective area of the piston and pressure difference on both sides; The hydraulic cylinder basically consists of cylinder barrel, cylinder head Inner Mongolia Cylinder Price The piston and piston rod, sealing device, buffer device and exhaust device are composed.

The two lips of the seal have two contact circumferential surfaces. Whether the force on the inner and outer circumferences is evenly distributed means that the force on the two circumferences cannot be zero. If the force on a certain point is zero, the shaft seal has inner and outer lips, Inner Mongolia Cylinder The outer lip is installed in the groove to contact the outer wall, and the inner lip is in contact with the piston rod surface. Both lips have an interference amount, which is equal to the generation of two contact circumferential surfaces, that is, the generation of two circumferential rebound forces. How to determine the magnitude of the circumferential force? Both the inner and outer lips of the seal have two chamfers. Since the interference of the same inner and outer lips is certain, Inner Mongolia Cylinder Price The angle of the chamfer determines the size of the circumferential area of the inner and outer contact of the two lips.

The connection between the oil cylinder and the actuator and the connection between the oil cylinder and the oil pipe cannot be the same, because there must be some differences between the connection between the oil cylinder and different products. In addition, during the use of the oil cylinder, it is necessary to avoid scratches, Inner Mongolia Cylinder Because if this problem occurs, it will affect the normal use of the oil cylinder. At present, there is no software for designing hydraulic cylinders, but there are design standards for hydraulic cylinders, and it is necessary to design hydraulic cylinders according to these standards. So far, Inner Mongolia Cylinder Price There is no software for designing hydraulic cylinders, but there are design standards for hydraulic cylinders.

If the piston rod of the hydraulic cylinder is not treated in time after being pulled, the normal use will be affected if it is light, and the operation will not be possible if it is heavy. The repair methods we adopt are local polishing to repair light draw marks, welding and manual polishing to repair heavy draw marks. Inner Mongolia Cylinder Through quenching and tempering treatment, the comprehensive mechanical properties of the cylinder piston rod with good strength and toughness matching were obtained. Inner Mongolia Cylinder Price The purpose of surface hardening is to obtain high surface hardness to support the chromium plating layer on the surface, so as to improve the wear resistance and corrosion resistance of the piston rod.

The hydraulic cylinder is the actuating element that converts hydraulic energy into mechanical energy in the hydraulic system. The faults can be basically summarized as hydraulic cylinder misoperation Inner Mongolia Cylinder Price It is unable to push the load and the piston slips or crawls. It is not uncommon for hydraulic cylinder failure to cause equipment shutdown. Therefore, Inner Mongolia Cylinder Attention should be paid to the fault diagnosis, use and maintenance of hydraulic cylinder. The main reason for excessive wear of piston seals is that the speed control valve is improperly adjusted, resulting in excessive back pressure, improper installation of seals or contamination of hydraulic oil. Secondly, foreign matters enter during assembly and the quality of sealing materials is poor.