上海新茶外卖高端

 Hydraulic cylinder manufacturer
Your current location: home page > Hot information

contact us Contact Us

Foshan Fuchao Hydraulic Electromechanical Equipment Co., Ltd

Mobile: 15975751599

Mobile: 13531395368

Tel.: 0757-85131606

Email: [email protected]

Website: uonetech.com.cn

Address: No. 26 and 27, Road 9, Zone 2, Xiedei Bridge, Guidan Avenue, Xiebian Second Industrial Zone, Dali Town, Nanhai District, Foshan City

Zhuhai professional hydraulic cylinder manufacturer

2020-10-14
 Zhuhai professional hydraulic cylinder manufacturer

Hydraulic oil cylinder is used in many industries. Once it fails, it will have a far-reaching impact and hinder the progress of all work. In fact, many customers said that the hydraulic cylinder could not operate, Zhuhai Hydraulic cylinder In order to solve this problem in time, we should first find out what causes the problem. Generally speaking, the problem that the hydraulic cylinder cannot act often occurs on the newly installed hydraulic cylinder, Zhuhai Hydraulic cylinder manufactor Generally, it is necessary to start from external reasons, such as whether the mechanism pulled by the hydraulic cylinder has excessive resistance, whether it is stuck, and whether it is against other parts; Whether the pressure at the oil inlet of the hydraulic cylinder is within the specified range.

 Zhuhai professional hydraulic cylinder manufacturer

For the selection of hydraulic cylinder, the hydraulic cylinder will be selected according to the inner diameter, stroke, operating pressure and installation type during the selection of hydraulic cylinder. In fact, in addition to these, we should pay attention to the following points. First, when the hydraulic cylinder is loaded and then the actuating speed reaches a certain standard, Zhuhai Hydraulic cylinder Hydraulic cylinder with buffer device must be used. Or when the speed reaches a higher speed, a deceleration valve must be installed outside the hydraulic cylinder; Secondly, carefully select hydraulic oil and oil seal. Oil seals of different materials are selected for different hydraulic oils, Zhuhai Hydraulic cylinder manufactor To ensure the service life of the hydraulic cylinder.

 Zhuhai professional hydraulic cylinder manufacturer

Before removing the hydraulic cylinder, depressurize the hydraulic circuit. Otherwise, when the oil pipe joint connected with the oil cylinder is loosened, Zhuhai Hydraulic cylinder The high-pressure oil in the circuit will be ejected rapidly. When the hydraulic circuit is depressurized, first loosen the hand wheel or pressure regulating screw at the overflow valve to unload the pressure oil, and then cut off the power supply or power source to stop the hydraulic device. During unloading, prevent damage to the thread at the top of the piston rod, the thread at the oil port, the surface of the piston rod, the inner wall of the cylinder liner, etc. Zhuhai Hydraulic cylinder manufactor In order to prevent the piston rod and other slender parts from bending or deformation, the skid shall be used to support and balance during placement.

 Zhuhai professional hydraulic cylinder manufacturer

The oil cylinder shall be assembled in a special workshop or assembly area, and the temperature shall be kept at 20~250C, Zhuhai Hydraulic cylinder manufactor It shall be far away from the tuyere, dust and cutting area, with fresh air, no dust and no noise; Avoid direct glare. The assembly room shall be equipped with installation platform, sufficient working position apparatus, assembly turnover vehicle Zhuhai Hydraulic cylinder Lifting and hoisting equipment and the following special basic equipment. a: Cylinder loader; b: Another cylinder cleaning machine is used to heat and clean another part; c: Pressure test equipment, used for pressure test of oil cylinder; d: The air duct is used to clean and dry the other parts after cleaning.

 Zhuhai professional hydraulic cylinder manufacturer

The connection between the oil cylinder and the actuator and the connection between the oil cylinder and the oil pipe cannot be the same, because there must be some differences between the connection between the oil cylinder and different products. In addition, during the use of the oil cylinder, it is necessary to avoid scratches, Zhuhai Hydraulic cylinder Because if this problem occurs, it will affect the normal use of the oil cylinder. At present, there is no software for designing hydraulic cylinders, but there are design standards for hydraulic cylinders, and it is necessary to design hydraulic cylinders according to these standards. So far, Zhuhai Hydraulic cylinder manufactor There is no software for designing hydraulic cylinders, but there are design standards for hydraulic cylinders.

home page             About us             Product display             Success stories             after-sale service             News Center             contact us

contact information           Site Map           Online Message

Tel: 15975751599/13531395368

Service hotline: 0757-85131606

Email: [email protected]

Address: No. 26 and 27, Road 9, Zone 2, Xiedei Bridge, Guidan Avenue, Xiebian Second Industrial Zone, Dali Town, Nanhai District, Foshan City

 Oil cylinder manufacturer

Service, service, heat and line

159-7575-1599

135-3139-5368

Copyright © Foshan Fuchao Hydraulic Electromechanical Equipment Co., Ltd. All rights reserved is mainly engaged in Oil cylinder manufacturer , Hydraulic cylinder manufacturer , Oil cylinder manufacturer Welcome to inquire!
Record No.: Service support: Statement: Part of the content and pictures of this site are from the Internet. If there is infringement, please contact the administrator to delete it at the first time. Thank you!
Main business area: Foshan Shenzhen Guangzhou Zhongshan Guangdong Zhuhai Dongguan Huizhou Guangxi Beijing