The oil cylinder shall be assembled in a special workshop or assembly area, and the temperature shall be kept at 20~250C, Liaoyuan Hydraulic equipment Manufacturer It shall be far away from the tuyere, dust and cutting area, with fresh air, no dust and no noise; Avoid direct glare. The assembly room shall be equipped with installation platform, sufficient working position apparatus, assembly turnover vehicle Liaoyuan Hydraulic equipment Lifting and hoisting equipment and the following special basic equipment. a: Cylinder loader; b: Another cylinder cleaning machine is used to heat and clean another part; c: Pressure test equipment, used for pressure test of oil cylinder; d: The air duct is used to clean and dry the other parts after cleaning.
Because the hydraulic cylinder has to bear a great pressure, the heavier the load, the greater its pressure will be. Therefore, the maintenance of the hydraulic cylinder is an important part of the maintenance of the entire hydraulic system. The hydraulic cylinder is the heart of the hydraulic system, Liaoyuan Hydraulic equipment It is difficult to repair the heart problem, so the maintenance of the hydraulic cylinder should be careful. First, rust prevention. Because the piston part of the hydraulic cylinder will extend the cylinder in the working state, Liaoyuan Hydraulic equipment Manufacturer Naturally, it will be corroded by oxide and acid gas, which requires us to coat it with proper grease for protection.
The connection between the oil cylinder and the actuator and the connection between the oil cylinder and the oil pipe cannot be the same, because there must be some differences between the connection between the oil cylinder and different products. In addition, during the use of the oil cylinder, it is necessary to avoid scratches, Liaoyuan Hydraulic equipment Because if this problem occurs, it will affect the normal use of the oil cylinder. At present, there is no software for designing hydraulic cylinders, but there are design standards for hydraulic cylinders, and it is necessary to design hydraulic cylinders according to these standards. So far, Liaoyuan Hydraulic equipment Manufacturer There is no software for designing hydraulic cylinders, but there are design standards for hydraulic cylinders.
Hydraulic oil cylinder is used in many industries. Once it fails, it will have a far-reaching impact and hinder the progress of all work. In fact, many customers said that the hydraulic cylinder could not operate, Liaoyuan Hydraulic equipment In order to solve this problem in time, we should first find out what causes the problem. Generally speaking, the problem that the hydraulic cylinder cannot act often occurs on the newly installed hydraulic cylinder, Liaoyuan Hydraulic equipment Manufacturer Generally, it is necessary to start from external reasons, such as whether the mechanism pulled by the hydraulic cylinder has excessive resistance, whether it is stuck, and whether it is against other parts; Whether the pressure at the oil inlet of the hydraulic cylinder is within the specified range.
If the piston rod of the hydraulic cylinder is not treated in time after being pulled, the normal use will be affected if it is light, and the operation will not be possible if it is heavy. The repair methods we adopt are local polishing to repair light draw marks, welding and manual polishing to repair heavy draw marks. Liaoyuan Hydraulic equipment Through quenching and tempering treatment, the comprehensive mechanical properties of the cylinder piston rod with good strength and toughness matching were obtained. Liaoyuan Hydraulic equipment Manufacturer The purpose of surface hardening is to obtain high surface hardness to support the chromium plating layer on the surface, so as to improve the wear resistance and corrosion resistance of the piston rod.
How to install and fix the hydraulic cylinder? There are two common ways to fix the hydraulic cylinder: the first is the square hydraulic cylinder fixed on the B plate, and the hydraulic cylinder needs to be positioned on the B plate. The second is a round hydraulic cylinder fixed on the ejector plate. It should be noted that the thimble plate locking screw needs to be added next to the hydraulic cylinder, and the force at this position is large, Liaoyuan Hydraulic equipment Prevent tension deformation. Another point is to inscribe words on the hydraulic cylinder, and write down the stroke of the hydraulic cylinder for easy verification. To correctly install the sealing device at each position of the hydraulic cylinder: Liaoyuan Hydraulic equipment Manufacturer When installing the O-ring seal, pay attention to its installation direction to avoid oil leakage due to installation. Its lip should face the oil chamber with pressure.
