If the piston rod of the hydraulic cylinder is not treated in time after being pulled, the normal use will be affected if it is light, and the operation will not be possible if it is heavy. The repair methods we adopt are local polishing to repair light draw marks, welding and manual polishing to repair heavy draw marks. Guangzhou Hydraulic equipment Through quenching and tempering treatment, the comprehensive mechanical properties of the cylinder piston rod with good strength and toughness matching were obtained. Guangzhou Hydraulic equipment Manufacturer The purpose of surface hardening is to obtain high surface hardness to support the chromium plating layer on the surface, so as to improve the wear resistance and corrosion resistance of the piston rod.

1. Internal leakage of oil cylinder; 2. Internal leakage at control valve hole and valve rod; 3. Overload overflow valve is poor; 4. The valve rod is not in the middle position; 5. PPC valve is not in the middle position. Hydraulic cylinder maintenance process: 1. Whether the hydraulic lock becomes normal when it is in the determined position, if so, check the PPC valve first; 2. Conduct oil cylinder plugging oil port test, Guangzhou Hydraulic equipment Check whether the oil cylinder is defective, and repair the oil cylinder if it is; 3. Replace the overload overflow valve and check whether it is the fault of the overload overflow valve; 4. Whether the valve rod is jammed, Guangzhou Hydraulic equipment Manufacturer Check again after cleaning, otherwise the main control valve needs to be repaired.

There are many hydraulic components on construction machinery, and sufficient hydraulic oil is required. When the hydraulic oil needs to be replaced due to its deterioration after a long time of use, some people mistakenly believe that only drain the oil in the hydraulic cylinder and fill it with new hydraulic oil. However, there are still many old hydraulic oils left in the hydraulic oil pipe and hydraulic control valve, Guangzhou Hydraulic equipment When the equipment is used, the mixing of new and old oil will speed up the deterioration of new oil. The correct oil change procedure should first drain the hydraulic oil in the hydraulic cylinder, Guangzhou Hydraulic equipment Manufacturer After cleaning the hydraulic cylinder, add new hydraulic oil, remove the circuit header, start the engine and run at low speed to make the oil pump work.

1、 If the groove is too deep, two situations will occur: A. If the gap between the seal root and the groove becomes larger, the seal root will become unstable. B. The interference between the sealing lip and the sealing surface becomes smaller, Guangzhou Hydraulic equipment The rebound force of the seal becomes smaller, and the failure rate of low-pressure oil leakage will increase when the piston rod jumps. 2、 If the groove is too shallow, two situations will also occur: A. The interference between the sealing lip and the sealing surface will increase, and the contact area will increase, which will lead to greater friction, Guangzhou Hydraulic equipment Manufacturer The increased heat accelerates the damage of the seal lip. B. As a result, the clearance at the seal root becomes smaller, and the probability of the seal root being squeezed out when the oil cylinder is under high pressure increases.

The speed ratio refers to the same flow (volume of liquid entering the hydraulic cylinder per unit time), Guangzhou Hydraulic equipment Manufacturer The ratio of the piston rod extension speed to the retraction speed. The calculation is equal to the inverse ratio of the large cavity area and the small cavity area of the cylinder. The speed ratio is related to the cylinder diameter and rod diameter of the oil cylinder. Main products: harvesting machinery series Guangzhou Hydraulic equipment Flip plow series, press series, grader series, TGL, HG, SG, DG series vehicle oil cylinder, HSG series engineering oil cylinder mining machinery, ship oil cylinder, and various non-standard oil cylinders. Welcome to order!

Select the cylinder type correctly according to the working requirements and conditions. It is required that there is no impact phenomenon and impact noise when the cylinder reaches the end of the stroke; Cushion cylinder shall be selected; Light weight is required; It is required to select light cylinder; Guangzhou Hydraulic equipment Narrow installation space and short stroke are required; It is required to select thin cylinder; It is required to have transverse load, and the cylinder with guide rod can be selected; High braking accuracy is required, and locking cylinder can be selected; It is not allowed to rotate the piston rod, and the cylinder with rod non rotation function can be selected; Guangzhou Hydraulic equipment Manufacturer In corrosive environment, corrosion-resistant steel cylinders shall be selected.