If the piston rod of the hydraulic cylinder is not treated in time after being pulled, the normal use will be affected if it is light, and the operation will not be possible if it is heavy. The repair methods we adopt are local polishing to repair light draw marks, welding and manual polishing to repair heavy draw marks. Changzhou Hydraulic cylinder Through quenching and tempering treatment, the comprehensive mechanical properties of the cylinder piston rod with good strength and toughness matching were obtained. Changzhou Hydraulic cylinder Manufacturer The purpose of surface hardening is to obtain high surface hardness to support the chromium plating layer on the surface, so as to improve the wear resistance and corrosion resistance of the piston rod.

1、 If the groove is too deep, two situations will occur: A. If the gap between the seal root and the groove becomes larger, the seal root will become unstable. B. The interference between the sealing lip and the sealing surface becomes smaller, Changzhou Hydraulic cylinder The rebound force of the seal becomes smaller, and the failure rate of low-pressure oil leakage will increase when the piston rod jumps. 2、 If the groove is too shallow, two situations will also occur: A. The interference between the sealing lip and the sealing surface will increase, and the contact area will increase, which will lead to greater friction, Changzhou Hydraulic cylinder Manufacturer The increased heat accelerates the damage of the seal lip. B. As a result, the clearance at the seal root becomes smaller, and the probability of the seal root being squeezed out when the oil cylinder is under high pressure increases.

The failure of the hydraulic cylinder due to improper design and manufacture is because the oil pressure cannot act on the effective working area of the piston when the piston travels to the end point and returns, or the effective working area is too small when starting, which causes problems. When the transverse load of the hydraulic cylinder is too large, the force is not strong or the cylinder is bitten, the same consequences will occur. Changzhou Hydraulic cylinder Therefore, when installing the hydraulic cylinder, the axis position of the cylinder must be consistent with the movement direction; Changzhou Hydraulic cylinder Manufacturer And ensure that the load borne by the hydraulic cylinder passes through the cylinder axis as far as possible without eccentricity, so that the problem can be solved.

Because the hydraulic cylinder has to bear a great pressure, the heavier the load, the greater its pressure will be. Therefore, the maintenance of the hydraulic cylinder is an important part of the maintenance of the entire hydraulic system. The hydraulic cylinder is the heart of the hydraulic system, Changzhou Hydraulic cylinder It is difficult to repair the heart problem, so the maintenance of the hydraulic cylinder should be careful. First, rust prevention. Because the piston part of the hydraulic cylinder will extend the cylinder in the working state, Changzhou Hydraulic cylinder Manufacturer Naturally, it will be corroded by oxide and acid gas, which requires us to coat it with proper grease for protection.

There are many hydraulic components on construction machinery, and sufficient hydraulic oil is required. When the hydraulic oil needs to be replaced due to its deterioration after a long time of use, some people mistakenly believe that it is only necessary to drain the oil in the hydraulic cylinder Changzhou Hydraulic cylinder Top up with new hydraulic oil. However, there are still many old hydraulic oils left in the hydraulic oil pipe and hydraulic control valve at this time. When the equipment is used, the mixing of new and old oils will speed up the deterioration of new oils. The correct oil change procedure should first drain the hydraulic oil in the hydraulic cylinder, clean the hydraulic cylinder, and then add new hydraulic oil, Changzhou Hydraulic cylinder Manufacturer Then remove the circuit header, start the engine and run at low speed to make the oil pump work and operate each mechanism separately.

The valve core of the flow valve in the hydraulic cylinder is blocked, which is easy to cause the action failure of the hydraulic cylinder. We need to check whether there are pollutants in the oil in the hydraulic cylinder and whether the valve body is worn. It is necessary to check whether the piston rod seal is too tight, Changzhou Hydraulic cylinder Whether there are pollutants entering, whether the axis line is aligned, and whether the easily damaged components fail. If the pressure controlled by the hydraulic system is too low, the action of the hydraulic cylinder will also fail, Changzhou Hydraulic cylinder Manufacturer At this time, it is necessary to check the control pressure source to ensure that the pressure value is consistent with the specified value of the system.