Hydraulic oil cylinder is used in many industries. Once it fails, it will have a far-reaching impact and hinder the progress of all work. In fact, many customers said that the hydraulic cylinder could not operate, Fujian Hydraulic cylinder In order to solve this problem in time, we should first find out what causes the problem. Generally speaking, the problem that the hydraulic cylinder cannot act often occurs on the newly installed hydraulic cylinder, Fujian Hydraulic cylinder Price Generally, it is necessary to start from external reasons, such as whether the mechanism pulled by the hydraulic cylinder has excessive resistance, whether it is stuck, and whether it is against other parts; Whether the pressure at the oil inlet of the hydraulic cylinder is within the specified range.

1、 If the groove is too deep, two situations will occur: A. If the gap between the seal root and the groove becomes larger, the seal root will become unstable. B. The interference between the sealing lip and the sealing surface becomes smaller, Fujian Hydraulic cylinder The rebound force of the seal becomes smaller, and the failure rate of low-pressure oil leakage will increase when the piston rod jumps. 2、 If the groove is too shallow, two situations will also occur: A. The interference between the sealing lip and the sealing surface will increase, and the contact area will increase, which will lead to greater friction, Fujian Hydraulic cylinder Price The increased heat accelerates the damage of the seal lip. B. As a result, the clearance at the seal root becomes smaller, and the probability of the seal root being squeezed out when the oil cylinder is under high pressure increases.

Before removing the hydraulic cylinder, depressurize the hydraulic circuit. Otherwise, when the oil pipe joint connected with the oil cylinder is loosened, Fujian Hydraulic cylinder The high-pressure oil in the circuit will be ejected rapidly. When the hydraulic circuit is depressurized, first loosen the hand wheel or pressure regulating screw at the overflow valve to unload the pressure oil, and then cut off the power supply or power source to stop the hydraulic device. During unloading, prevent damage to the thread at the top of the piston rod, the thread at the oil port, the surface of the piston rod, the inner wall of the cylinder liner, etc. Fujian Hydraulic cylinder Price In order to prevent the piston rod and other slender parts from bending or deformation, the skid shall be used to support and balance during placement.

For the selection of hydraulic cylinder, the hydraulic cylinder will be selected according to the inner diameter, stroke, operating pressure and installation type during the selection of hydraulic cylinder. In fact, in addition to these, we should pay attention to the following points. First, when the hydraulic cylinder is loaded and then the actuating speed reaches a certain standard, Fujian Hydraulic cylinder Hydraulic cylinder with buffer device must be used. Or when the speed reaches a higher speed, a deceleration valve must be installed outside the hydraulic cylinder; Secondly, carefully select hydraulic oil and oil seal. Oil seals of different materials are selected for different hydraulic oils, Fujian Hydraulic cylinder Price To ensure the service life of the hydraulic cylinder.

The failure of the hydraulic cylinder due to improper design and manufacture is because the oil pressure cannot act on the effective working area of the piston when the piston travels to the end point and returns, or the effective working area is too small when starting, which causes problems. When the transverse load of the hydraulic cylinder is too large, the force is not strong or the cylinder is bitten, the same consequences will occur. Fujian Hydraulic cylinder Therefore, when installing the hydraulic cylinder, the axis position of the cylinder must be consistent with the movement direction; Fujian Hydraulic cylinder Price And ensure that the load borne by the hydraulic cylinder passes through the cylinder axis as far as possible without eccentricity, so that the problem can be solved.

The connection between the oil cylinder and the actuator and the connection between the oil cylinder and the oil pipe cannot be the same, because there must be some differences between the connection between the oil cylinder and different products. In addition, during the use of the oil cylinder, it is necessary to avoid scratches, Fujian Hydraulic cylinder Because if this problem occurs, it will affect the normal use of the oil cylinder. At present, there is no software for designing hydraulic cylinders, but there are design standards for hydraulic cylinders, and it is necessary to design hydraulic cylinders according to these standards. So far, Fujian Hydraulic cylinder Price There is no software for designing hydraulic cylinders, but there are design standards for hydraulic cylinders.