1、 If the groove is too deep, two situations will occur: A. If the gap between the seal root and the groove becomes larger, the seal root will become unstable. B. The interference between the sealing lip and the sealing surface becomes smaller, Guiyang Hydraulic machinery The rebound force of the seal becomes smaller, and the failure rate of low-pressure oil leakage will increase when the piston rod jumps. 2、 If the groove is too shallow, two situations will also occur: A. The interference between the sealing lip and the sealing surface will increase, and the contact area will increase, which will lead to greater friction, Guiyang Hydraulic machinery Price The increased heat accelerates the damage of the seal lip. B. As a result, the clearance at the seal root becomes smaller, and the probability of the seal root being squeezed out when the oil cylinder is under high pressure increases.
The connection between the oil cylinder and the actuator and the connection between the oil cylinder and the oil pipe cannot be the same, because there must be some differences between the connection between the oil cylinder and different products. In addition, during the use of the oil cylinder, it is necessary to avoid scratches, Guiyang Hydraulic machinery Because if this problem occurs, it will affect the normal use of the oil cylinder. At present, there is no software for designing hydraulic cylinders, but there are design standards for hydraulic cylinders, and it is necessary to design hydraulic cylinders according to these standards. So far, Guiyang Hydraulic machinery Price There is no software for designing hydraulic cylinders, but there are design standards for hydraulic cylinders.
1. There are many factors that cause this problem. First, measure the pressure of the main system to see whether the pressure of the main system in the pressure holding state is consistent with the initial setting. Check the hydraulic oil and suction oil filter before measuring the pressure, Guiyang Hydraulic machinery Replace or clean it. Secondly, check the main overflow valve of the reversing control multi way valve to see if it is damaged or blocked by foreign matters, Guiyang Hydraulic machinery Price Clean it. If your pump is a gear pump, the problem should be minor in general. 2. Next, let's look at the traffic problem.
The two lips of the seal have two contact circumferential surfaces. Whether the force on the inner and outer circumferences is evenly distributed means that the force on the two circumferences cannot be zero. If the force on a certain point is zero, the shaft seal has inner and outer lips, Guiyang Hydraulic machinery The outer lip is installed in the groove to contact the outer wall, and the inner lip is in contact with the piston rod surface. Both lips have an interference amount, which is equal to the generation of two contact circumferential surfaces, that is, the generation of two circumferential rebound forces. How to determine the magnitude of the circumferential force? Both the inner and outer lips of the seal have two chamfers. Since the interference of the same inner and outer lips is certain, Guiyang Hydraulic machinery Price The angle of the chamfer determines the size of the circumferential area of the inner and outer contact of the two lips.
Compared with mechanical transmission, hydraulic cylinder transmission is a new transmission form. Hydraulic transmission has a history of more than 200 years since the birth of hydraulic press, but hydraulic transmission has been going on for many years. Especially after the 1960s, with the development of atomic energy science, space and hydraulic technology, Guiyang Hydraulic machinery It permeates all fields of the national economy, including agricultural machinery, automobiles, light textile, shipbuilding, petroleum, aviation and machine tool industries, Guiyang Hydraulic machinery Price Hydraulic technology lists some application examples of hydraulic and pneumatic transmission.
It is suitable for hydraulic transmission of construction machinery, lifting, transportation machinery and mining machinery. Hydraulic transmission principle - oil is used as working medium, Guiyang Hydraulic machinery The movement is transmitted through the change of sealing volume, and the power is transmitted through the pressure inside the oil. 1. Power part - converts mechanical energy of prime mover into pressure energy (hydraulic energy) of oil. For example: hydraulic pump. 2. Executive part - converts the oil pressure energy input by the hydraulic pump into the mechanical energy driving the working mechanism. For example: hydraulic cylinder, hydraulic motor. 3. Control part - used to control and adjust the oil pressure Guiyang Hydraulic machinery Price Flow rate and flow direction. For example: pressure control valve, flow control valve.
