How to install and fix the hydraulic cylinder? There are two common ways to fix the hydraulic cylinder: the first is the square hydraulic cylinder fixed on the B plate, and the hydraulic cylinder needs to be positioned on the B plate. The second is a round hydraulic cylinder fixed on the ejector plate. It should be noted that the thimble plate locking screw needs to be added next to the hydraulic cylinder, and the force at this position is large, Shenyang Hydraulic system Prevent tension deformation. Another point is to inscribe words on the hydraulic cylinder, and write down the stroke of the hydraulic cylinder for easy verification. To correctly install the sealing device at each position of the hydraulic cylinder: Shenyang Hydraulic system Price When installing the O-ring seal, pay attention to its installation direction to avoid oil leakage due to installation. Its lip should face the oil chamber with pressure.

Select the cylinder type correctly according to the working requirements and conditions. It is required that there is no impact phenomenon and impact noise when the cylinder reaches the end of the stroke; Cushion cylinder shall be selected; Light weight is required; It is required to select light cylinder; Shenyang Hydraulic system Narrow installation space and short stroke are required; It is required to select thin cylinder; It is required to have transverse load, and the cylinder with guide rod can be selected; High braking accuracy is required, and locking cylinder can be selected; It is not allowed to rotate the piston rod, and the cylinder with rod non rotation function can be selected; Shenyang Hydraulic system Price In corrosive environment, corrosion-resistant steel cylinders shall be selected.

The connection between the oil cylinder and the actuator and the connection between the oil cylinder and the oil pipe cannot be the same, because there must be some differences between the connection between the oil cylinder and different products. In addition, during the use of the oil cylinder, it is necessary to avoid scratches, Shenyang Hydraulic system Because if this problem occurs, it will affect the normal use of the oil cylinder. At present, there is no software for designing hydraulic cylinders, but there are design standards for hydraulic cylinders, and it is necessary to design hydraulic cylinders according to these standards. So far, Shenyang Hydraulic system Price There is no software for designing hydraulic cylinders, but there are design standards for hydraulic cylinders.

Items to be checked when the speed of hydraulic cylinder slows down. 1. Where and what type of oil cylinder has been used for several years, Shenyang Hydraulic system What is the working pressure. You don't have any of these. How can I troubleshoot them for you. Check the lower seal if there is internal leakage. 2. It is likely that the internal working pressure of the oil cylinder has decreased. 3. Check whether the system is blocked, Shenyang Hydraulic system Price In addition, check whether the oil cylinder seal ring is damaged, and then check whether the piston rod is damaged. Basically, these aspects can identify the problem.

There are many hydraulic components on construction machinery, and sufficient hydraulic oil is required. When the hydraulic oil needs to be replaced due to its deterioration after a long time of use, some people mistakenly believe that only drain the oil in the hydraulic cylinder and fill it with new hydraulic oil. However, there are still many old hydraulic oils left in the hydraulic oil pipe and hydraulic control valve, Shenyang Hydraulic system When the equipment is used, the mixing of new and old oil will speed up the deterioration of new oil. The correct oil change procedure should first drain the hydraulic oil in the hydraulic cylinder, Shenyang Hydraulic system Price After cleaning the hydraulic cylinder, add new hydraulic oil, remove the circuit header, start the engine and run at low speed to make the oil pump work.

Hydraulic cylinder is a hydraulic actuator that converts hydraulic energy into mechanical energy and performs linear reciprocating motion (or swing motion). It is simple in structure and reliable in operation. When it is used to realize reciprocating movement, the reducer can be avoided, Shenyang Hydraulic system And there is no transmission clearance, smooth movement, so it is widely used in various mechanical hydraulic systems. Output force of the hydraulic cylinder is proportional to effective area of the piston and pressure difference on both sides; The hydraulic cylinder basically consists of cylinder barrel, cylinder head Shenyang Hydraulic system Price The piston and piston rod, sealing device, buffer device and exhaust device are composed.