The valve core of the flow valve in the hydraulic cylinder is blocked, which is easy to cause the action failure of the hydraulic cylinder. We need to check whether there are pollutants in the oil in the hydraulic cylinder and whether the valve body is worn. It is necessary to check whether the piston rod seal is too tight, Jingdezhen Hydraulic equipment Whether there are pollutants entering, whether the axis line is aligned, and whether the easily damaged components fail. If the pressure controlled by the hydraulic system is too low, the action of the hydraulic cylinder will also fail, Jingdezhen Hydraulic equipment Price At this time, it is necessary to check the control pressure source to ensure that the pressure value is consistent with the specified value of the system.
1. Internal leakage of oil cylinder; 2. Internal leakage at control valve hole and valve rod; 3. Overload overflow valve is poor; 4. The valve rod is not in the middle position; 5. PPC valve is not in the middle position. Hydraulic cylinder maintenance process: 1. Whether the hydraulic lock becomes normal when it is in the determined position, if so, check the PPC valve first; 2. Conduct oil cylinder plugging oil port test, Jingdezhen Hydraulic equipment Check whether the oil cylinder is defective, and repair the oil cylinder if it is; 3. Replace the overload overflow valve and check whether it is the fault of the overload overflow valve; 4. Whether the valve rod is jammed, Jingdezhen Hydraulic equipment Price Check again after cleaning, otherwise the main control valve needs to be repaired.
It is suitable for hydraulic transmission of construction machinery, lifting, transportation machinery and mining machinery. Hydraulic transmission principle - oil is used as working medium, Jingdezhen Hydraulic equipment The movement is transmitted through the change of sealing volume, and the power is transmitted through the pressure inside the oil. 1. Power part - converts mechanical energy of prime mover into pressure energy (hydraulic energy) of oil. For example: hydraulic pump. 2. Executive part - converts the oil pressure energy input by the hydraulic pump into the mechanical energy driving the working mechanism. For example: hydraulic cylinder, hydraulic motor. 3. Control part - used to control and adjust the oil pressure Jingdezhen Hydraulic equipment Price Flow rate and flow direction. For example: pressure control valve, flow control valve.
Select the cylinder type correctly according to the working requirements and conditions. It is required that there is no impact phenomenon and impact noise when the cylinder reaches the end of the stroke; Cushion cylinder shall be selected; Light weight is required; It is required to select light cylinder; Jingdezhen Hydraulic equipment Narrow installation space and short stroke are required; It is required to select thin cylinder; It is required to have transverse load, and the cylinder with guide rod can be selected; High braking accuracy is required, and locking cylinder can be selected; It is not allowed to rotate the piston rod, and the cylinder with rod non rotation function can be selected; Jingdezhen Hydraulic equipment Price In corrosive environment, corrosion-resistant steel cylinders shall be selected.
The hydraulic cylinder is the actuating element that converts hydraulic energy into mechanical energy in the hydraulic system. The faults can be basically summarized as hydraulic cylinder misoperation Jingdezhen Hydraulic equipment Price It is unable to push the load and the piston slips or crawls. It is not uncommon for hydraulic cylinder failure to cause equipment shutdown. Therefore, Jingdezhen Hydraulic equipment Attention should be paid to the fault diagnosis, use and maintenance of hydraulic cylinder. The main reason for excessive wear of piston seals is that the speed control valve is improperly adjusted, resulting in excessive back pressure, improper installation of seals or contamination of hydraulic oil. Secondly, foreign matters enter during assembly and the quality of sealing materials is poor.
Before removing the hydraulic cylinder, depressurize the hydraulic circuit. Otherwise, when the oil pipe joint connected with the oil cylinder is loosened, Jingdezhen Hydraulic equipment The high-pressure oil in the circuit will be ejected rapidly. When the hydraulic circuit is depressurized, first loosen the hand wheel or pressure regulating screw at the overflow valve to unload the pressure oil, and then cut off the power supply or power source to stop the hydraulic device. During unloading, prevent damage to the thread at the top of the piston rod, the thread at the oil port, the surface of the piston rod, the inner wall of the cylinder liner, etc. Jingdezhen Hydraulic equipment Price In order to prevent the piston rod and other slender parts from bending or deformation, the skid shall be used to support and balance during placement.
