As the structure and size of various hydraulic cylinders are different, the disassembly sequence is slightly different. Generally, drain the oil in the two chambers of the oil cylinder, remove the cylinder head, and finally remove the piston and piston rod. Jiangsu Hydraulic machinery When disassembling the cylinder head of the hydraulic cylinder, special tools shall be used for the key or snap ring of the internal key type connection, and flat shovel is prohibited; Flange end caps must be pushed out with screws, and hammering or hard prying is not allowed. When it is difficult to draw out the piston and piston rod, do not force them out, Jiangsu Hydraulic machinery manufactor The reason shall be found out before disassembly. Before and after unloading, try to create conditions to prevent the parts of the hydraulic cylinder from being polluted by the surrounding dust and impurities.

The two lips of the seal have two contact circumferential surfaces. Whether the force on the inner and outer circumferences is evenly distributed means that the force on the two circumferences cannot be zero. If the force on a certain point is zero, the shaft seal has inner and outer lips, Jiangsu Hydraulic machinery The outer lip is installed in the groove to contact the outer wall, and the inner lip is in contact with the piston rod surface. Both lips have an interference amount, which is equal to the generation of two contact circumferential surfaces, that is, the generation of two circumferential rebound forces. How to determine the magnitude of the circumferential force? Both the inner and outer lips of the seal have two chamfers. Since the interference of the same inner and outer lips is certain, Jiangsu Hydraulic machinery manufactor The angle of the chamfer determines the size of the circumferential area of the inner and outer contact of the two lips.

The oil cylinder shall be assembled in a special workshop or assembly area, and the temperature shall be kept at 20~250C, Jiangsu Hydraulic machinery manufactor It shall be far away from the tuyere, dust and cutting area, with fresh air, no dust and no noise; Avoid direct glare. The assembly room shall be equipped with installation platform, sufficient working position apparatus, assembly turnover vehicle Jiangsu Hydraulic machinery Lifting and hoisting equipment and the following special basic equipment. a: Cylinder loader; b: Another cylinder cleaning machine is used to heat and clean another part; c: Pressure test equipment, used for pressure test of oil cylinder; d: The air duct is used to clean and dry the other parts after cleaning.

There are many hydraulic components on construction machinery, and sufficient hydraulic oil is required. When the hydraulic oil needs to be replaced due to its deterioration after a long time of use, some people mistakenly believe that it is only necessary to drain the oil in the hydraulic cylinder Jiangsu Hydraulic machinery Top up with new hydraulic oil. However, there are still many old hydraulic oils left in the hydraulic oil pipe and hydraulic control valve at this time. When the equipment is used, the mixing of new and old oils will speed up the deterioration of new oils. The correct oil change procedure should first drain the hydraulic oil in the hydraulic cylinder, clean the hydraulic cylinder, and then add new hydraulic oil, Jiangsu Hydraulic machinery manufactor Then remove the circuit header, start the engine and run at low speed to make the oil pump work and operate each mechanism separately.

Because the hydraulic cylinder has to bear a great pressure, the heavier the load, the greater its pressure will be. Therefore, the maintenance of the hydraulic cylinder is an important part of the maintenance of the entire hydraulic system. The hydraulic cylinder is the heart of the hydraulic system, Jiangsu Hydraulic machinery It is difficult to repair the heart problem, so the maintenance of the hydraulic cylinder should be careful. First, rust prevention. Because the piston part of the hydraulic cylinder will extend the cylinder in the working state, Jiangsu Hydraulic machinery manufactor Naturally, it will be corroded by oxide and acid gas, which requires us to coat it with proper grease for protection.

The speed ratio refers to the same flow (volume of liquid entering the hydraulic cylinder per unit time), Jiangsu Hydraulic machinery manufactor The ratio of the piston rod extension speed to the retraction speed. The calculation is equal to the inverse ratio of the large cavity area and the small cavity area of the cylinder. The speed ratio is related to the cylinder diameter and rod diameter of the oil cylinder. Main products: harvesting machinery series Jiangsu Hydraulic machinery Flip plow series, press series, grader series, TGL, HG, SG, DG series vehicle oil cylinder, HSG series engineering oil cylinder mining machinery, ship oil cylinder, and various non-standard oil cylinders. Welcome to order!