As the structure and size of various hydraulic cylinders are different, the disassembly sequence is slightly different. Generally, drain the oil in the two chambers of the oil cylinder, remove the cylinder head, and finally remove the piston and piston rod. Xingtai Cylinder When disassembling the cylinder head of the hydraulic cylinder, special tools shall be used for the key or snap ring of the internal key type connection, and flat shovel is prohibited; Flange end caps must be pushed out with screws, and hammering or hard prying is not allowed. When it is difficult to draw out the piston and piston rod, do not force them out, Xingtai Cylinder manufactor The reason shall be found out before disassembly. Before and after unloading, try to create conditions to prevent the parts of the hydraulic cylinder from being polluted by the surrounding dust and impurities.

Select the cylinder type correctly according to the working requirements and conditions. It is required that there is no impact phenomenon and impact noise when the cylinder reaches the end of the stroke; Cushion cylinder shall be selected; Light weight is required; It is required to select light cylinder; Xingtai Cylinder Narrow installation space and short stroke are required; It is required to select thin cylinder; It is required to have transverse load, and the cylinder with guide rod can be selected; High braking accuracy is required, and locking cylinder can be selected; It is not allowed to rotate the piston rod, and the cylinder with rod non rotation function can be selected; Xingtai Cylinder manufactor In corrosive environment, corrosion-resistant steel cylinders shall be selected.

1、 If the groove is too deep, two situations will occur: A. If the gap between the seal root and the groove becomes larger, the seal root will become unstable. B. The interference between the sealing lip and the sealing surface becomes smaller, Xingtai Cylinder The rebound force of the seal becomes smaller, and the failure rate of low-pressure oil leakage will increase when the piston rod jumps. 2、 If the groove is too shallow, two situations will also occur: A. The interference between the sealing lip and the sealing surface will increase, and the contact area will increase, which will lead to greater friction, Xingtai Cylinder manufactor The increased heat accelerates the damage of the seal lip. B. As a result, the clearance at the seal root becomes smaller, and the probability of the seal root being squeezed out when the oil cylinder is under high pressure increases.

The hydraulic cylinder is the actuating element that converts hydraulic energy into mechanical energy in the hydraulic system. The faults can be basically summarized as hydraulic cylinder misoperation Xingtai Cylinder manufactor It is unable to push the load and the piston slips or crawls. It is not uncommon for hydraulic cylinder failure to cause equipment shutdown. Therefore, Xingtai Cylinder Attention should be paid to the fault diagnosis, use and maintenance of hydraulic cylinder. The main reason for excessive wear of piston seals is that the speed control valve is improperly adjusted, resulting in excessive back pressure, improper installation of seals or contamination of hydraulic oil. Secondly, foreign matters enter during assembly and the quality of sealing materials is poor.

The hydraulic system is composed of various hydraulic components. All hydraulic components are organically connected into a complete hydraulic system by pipes, joints, integrated valve blocks and other parts. Therefore, whether the hydraulic pipeline is installed correctly Xingtai Cylinder Firm, reliable and neat will have an important impact on the working performance of the hydraulic system. Check the quality of pipes. Find out the pipe material Xingtai Cylinder manufactor Whether the size and quality meet the design requirements; Check whether there is serious flattening or bending on the appearance of the pipe, whether there is corrosion on the surface of the inner and outer walls of the pipe, whether there is crack on the outer wall and other defects.

The connection between the oil cylinder and the actuator and the connection between the oil cylinder and the oil pipe cannot be the same, because there must be some differences between the connection between the oil cylinder and different products. In addition, during the use of the oil cylinder, it is necessary to avoid scratches, Xingtai Cylinder Because if this problem occurs, it will affect the normal use of the oil cylinder. At present, there is no software for designing hydraulic cylinders, but there are design standards for hydraulic cylinders, and it is necessary to design hydraulic cylinders according to these standards. So far, Xingtai Cylinder manufactor There is no software for designing hydraulic cylinders, but there are design standards for hydraulic cylinders.