As the structure and size of various hydraulic cylinders are different, the disassembly sequence is slightly different. Generally, drain the oil in the two chambers of the oil cylinder, remove the cylinder head, and finally remove the piston and piston rod. Ningbo Hydraulic cylinder When disassembling the cylinder head of the hydraulic cylinder, special tools shall be used for the key or snap ring of the internal key type connection, and flat shovel is prohibited; Flange end caps must be pushed out with screws, and hammering or hard prying is not allowed. When it is difficult to draw out the piston and piston rod, do not force them out, Ningbo Hydraulic cylinder Price The reason shall be found out before disassembly. Before and after unloading, try to create conditions to prevent the parts of the hydraulic cylinder from being polluted by the surrounding dust and impurities.

The hydraulic system is composed of various hydraulic components. All hydraulic components are organically connected into a complete hydraulic system by pipes, joints, integrated valve blocks and other parts. Therefore, whether the hydraulic pipeline is installed correctly Ningbo Hydraulic cylinder Firm, reliable and neat will have an important impact on the working performance of the hydraulic system. Check the quality of pipes. Find out the pipe material Ningbo Hydraulic cylinder Price Whether the size and quality meet the design requirements; Check whether there is serious flattening or bending on the appearance of the pipe, whether there is corrosion on the surface of the inner and outer walls of the pipe, whether there is crack on the outer wall and other defects.

For the same hydraulic cylinder on the Internet, some manufacturers quote more than 1200, some more than 1600, some about 1800, and even some about 3000. This situation makes the purchasing manufacturers feel puzzled and very difficult. Most manufacturers have limited procurement funds, Ningbo Hydraulic cylinder Therefore, if you want to achieve the predetermined purchase goal, you need to choose the hydraulic cylinder with high cost performance ratio, good quality and low price. However, the price gap of hydraulic cylinders in the market is staggering, Ningbo Hydraulic cylinder Price If you choose cheap oil cylinder rashly, the quality cannot be guaranteed, which will lead to endless troubles.

Hydraulic cylinder is a hydraulic actuator that converts hydraulic energy into mechanical energy and performs linear reciprocating motion (or swing motion). It is simple in structure and reliable in operation. When it is used to realize reciprocating movement, the reducer can be avoided, Ningbo Hydraulic cylinder And there is no transmission clearance, smooth movement, so it is widely used in various mechanical hydraulic systems. Output force of the hydraulic cylinder is proportional to effective area of the piston and pressure difference on both sides; The hydraulic cylinder basically consists of cylinder barrel, cylinder head Ningbo Hydraulic cylinder Price The piston and piston rod, sealing device, buffer device and exhaust device are composed.

The oil cylinder shall be assembled in a special workshop or assembly area, and the temperature shall be kept at 20~250C, Ningbo Hydraulic cylinder Price It shall be far away from the tuyere, dust and cutting area, with fresh air, no dust and no noise; Avoid direct glare. The assembly room shall be equipped with installation platform, sufficient working position apparatus, assembly turnover vehicle Ningbo Hydraulic cylinder Lifting and hoisting equipment and the following special basic equipment. a: Cylinder loader; b: Another cylinder cleaning machine is used to heat and clean another part; c: Pressure test equipment, used for pressure test of oil cylinder; d: The air duct is used to clean and dry the other parts after cleaning.

1. Internal leakage of oil cylinder; 2. Internal leakage at control valve hole and valve rod; 3. Overload overflow valve is poor; 4. The valve rod is not in the middle position; 5. PPC valve is not in the middle position. Hydraulic cylinder maintenance process: 1. Whether the hydraulic lock becomes normal when it is in the determined position, if so, check the PPC valve first; 2. Conduct oil cylinder plugging oil port test, Ningbo Hydraulic cylinder Check whether the oil cylinder is defective, and repair the oil cylinder if it is; 3. Replace the overload overflow valve and check whether it is the fault of the overload overflow valve; 4. Whether the valve rod is jammed, Ningbo Hydraulic cylinder Price Check again after cleaning, otherwise the main control valve needs to be repaired.