1. Internal leakage of oil cylinder; 2. Internal leakage at control valve hole and valve rod; 3. Overload overflow valve is poor; 4. The valve rod is not in the middle position; 5. PPC valve is not in the middle position. Hydraulic cylinder maintenance process: 1. Whether the hydraulic lock becomes normal when it is in the determined position, if so, check the PPC valve first; 2. Conduct oil cylinder plugging oil port test, city in Guangxi Hydraulic cylinder Check whether the oil cylinder is defective, and repair the oil cylinder if it is; 3. Replace the overload overflow valve and check whether it is the fault of the overload overflow valve; 4. Whether the valve rod is jammed, city in Guangxi Hydraulic cylinder manufactor Check again after cleaning, otherwise the main control valve needs to be repaired.

Because the hydraulic cylinder must bear a great pressure, the heavier the load, the greater its pressure will be. Therefore, the maintenance of the hydraulic cylinder is the most important part of the maintenance of the entire hydraulic system. The hydraulic cylinder is the heart of the hydraulic system. It is difficult to repair a heart problem, so the maintenance of the hydraulic cylinder should be careful. first, city in Guangxi Hydraulic cylinder Rust prevention is required. Because the piston part of the hydraulic cylinder will extend out of the cylinder in the working state, it will naturally suffer from oxidation city in Guangxi Hydraulic cylinder manufactor The erosion of acid gas requires us to apply proper amount of grease to protect it.

Select the cylinder type correctly according to the working requirements and conditions. It is required that there is no impact phenomenon and impact noise when the cylinder reaches the end of the stroke; Cushion cylinder shall be selected; Light weight is required; It is required to select light cylinder; city in Guangxi Hydraulic cylinder Narrow installation space and short stroke are required; It is required to select thin cylinder; It is required to have transverse load, and the cylinder with guide rod can be selected; High braking accuracy is required, and locking cylinder can be selected; It is not allowed to rotate the piston rod, and the cylinder with rod non rotation function can be selected; city in Guangxi Hydraulic cylinder manufactor In corrosive environment, corrosion-resistant steel cylinders shall be selected.

As the structure and size of various hydraulic cylinders are different, the disassembly sequence is slightly different. Generally, drain the oil in the two chambers of the oil cylinder, remove the cylinder head, and finally remove the piston and piston rod. city in Guangxi Hydraulic cylinder When disassembling the cylinder head of the hydraulic cylinder, special tools shall be used for the key or snap ring of the internal key type connection, and flat shovel is prohibited; Flange end caps must be pushed out with screws, and hammering or hard prying is not allowed. When it is difficult to draw out the piston and piston rod, do not force them out, city in Guangxi Hydraulic cylinder manufactor The reason shall be found out before disassembly. Before and after unloading, try to create conditions to prevent the parts of the hydraulic cylinder from being polluted by the surrounding dust and impurities.

1、 If the groove is too deep, two situations will occur: A. If the gap between the seal root and the groove becomes larger, the seal root will become unstable. B. The interference between the sealing lip and the sealing surface becomes smaller, city in Guangxi Hydraulic cylinder The rebound force of the seal becomes smaller, and the failure rate of low-pressure oil leakage will increase when the piston rod jumps. 2、 If the groove is too shallow, two situations will also occur: A. The interference between the sealing lip and the sealing surface will increase, and the contact area will increase, which will lead to greater friction, city in Guangxi Hydraulic cylinder manufactor The increased heat accelerates the damage of the seal lip. B. As a result, the clearance at the seal root becomes smaller, and the probability of the seal root being squeezed out when the oil cylinder is under high pressure increases.

Compared with mechanical transmission, hydraulic cylinder transmission is a new transmission form. Hydraulic transmission has a history of more than 200 years since the birth of hydraulic press, but hydraulic transmission has been going on for many years. Especially after the 1960s, with the development of atomic energy science, space and hydraulic technology, city in Guangxi Hydraulic cylinder It permeates all fields of the national economy, including agricultural machinery, automobiles, light textile, shipbuilding, petroleum, aviation and machine tool industries, city in Guangxi Hydraulic cylinder manufactor Hydraulic technology lists some application examples of hydraulic and pneumatic transmission.