The hydraulic cylinder is the actuating element that converts hydraulic energy into mechanical energy in the hydraulic system. The faults can be basically summarized as hydraulic cylinder misoperation Jiaxing Hydraulic equipment Price It is unable to push the load and the piston slips or crawls. It is not uncommon for hydraulic cylinder failure to cause equipment shutdown. Therefore, Jiaxing Hydraulic equipment Attention should be paid to the fault diagnosis, use and maintenance of hydraulic cylinder. The main reason for excessive wear of piston seals is that the speed control valve is improperly adjusted, resulting in excessive back pressure, improper installation of seals or contamination of hydraulic oil. Secondly, foreign matters enter during assembly and the quality of sealing materials is poor.

For the selection of hydraulic cylinder, the hydraulic cylinder will be selected according to the inner diameter, stroke, operating pressure and installation type during the selection of hydraulic cylinder. In fact, in addition to these, we should pay attention to the following points. First, when the hydraulic cylinder is loaded and then the actuating speed reaches a certain standard, Jiaxing Hydraulic equipment Hydraulic cylinder with buffer device must be used. Or when the speed reaches a higher speed, a deceleration valve must be installed outside the hydraulic cylinder; Secondly, carefully select hydraulic oil and oil seal. Oil seals of different materials are selected for different hydraulic oils, Jiaxing Hydraulic equipment Price To ensure the service life of the hydraulic cylinder.

1、 If the groove is too deep, two situations will occur: A. If the gap between the seal root and the groove becomes larger, the seal root will become unstable. B. The interference between the sealing lip and the sealing surface becomes smaller, Jiaxing Hydraulic equipment The rebound force of the seal becomes smaller, and the failure rate of low-pressure oil leakage will increase when the piston rod jumps. 2、 If the groove is too shallow, two situations will also occur: A. The interference between the sealing lip and the sealing surface will increase, and the contact area will increase, which will lead to greater friction, Jiaxing Hydraulic equipment Price The increased heat accelerates the damage of the seal lip. B. As a result, the clearance at the seal root becomes smaller, and the probability of the seal root being squeezed out when the oil cylinder is under high pressure increases.

The oil cylinder shall be assembled in a special workshop or assembly area, and the temperature shall be kept at 20~250C, Jiaxing Hydraulic equipment Price It shall be far away from the tuyere, dust and cutting area, with fresh air, no dust and no noise; Avoid direct glare. The assembly room shall be equipped with installation platform, sufficient working position apparatus, assembly turnover vehicle Jiaxing Hydraulic equipment Lifting and hoisting equipment and the following special basic equipment. a: Cylinder loader; b: Another cylinder cleaning machine is used to heat and clean another part; c: Pressure test equipment, used for pressure test of oil cylinder; d: The air duct is used to clean and dry the other parts after cleaning.

Hydraulic cylinder is a hydraulic actuator that converts hydraulic energy into mechanical energy and performs linear reciprocating motion (or swing motion). It is simple in structure and reliable in operation. When it is used to realize reciprocating movement, the reducer can be avoided, Jiaxing Hydraulic equipment And there is no transmission clearance, smooth movement, so it is widely used in various mechanical hydraulic systems. Output force of the hydraulic cylinder is proportional to effective area of the piston and pressure difference on both sides; The hydraulic cylinder basically consists of cylinder barrel, cylinder head Jiaxing Hydraulic equipment Price The piston and piston rod, sealing device, buffer device and exhaust device are composed.

Fluid cleanliness. The cleanliness of the system oil will have a very important impact on the hydraulic cylinder. Hydraulic shock and vibration hydraulic cylinders will be affected by the performance of components, pipeline and medium characteristics, etc., which will be accompanied by hydraulic shock and vibration. Generally speaking, if the oil temperature is too high or too low, Jiaxing Hydraulic equipment Price Will have a great impact on the working efficiency of the hydraulic cylinder. If the oil temperature of the hydraulic cylinder is too high or too low, the physical and chemical properties of the medium will change, Jiaxing Hydraulic equipment As a result, the viscosity of the working medium decreases or the possibility of leakage increases.