There are many hydraulic components on construction machinery, and sufficient hydraulic oil is required. When the hydraulic oil needs to be replaced due to its deterioration after a long time of use, some people mistakenly believe that only drain the oil in the hydraulic cylinder and fill it with new hydraulic oil. However, there are still many old hydraulic oils left in the hydraulic oil pipe and hydraulic control valve, Yibin Oil cylinder When the equipment is used, the mixing of new and old oil will speed up the deterioration of new oil. The correct oil change procedure should first drain the hydraulic oil in the hydraulic cylinder, Yibin Oil cylinder Price After cleaning the hydraulic cylinder, add new hydraulic oil, remove the circuit header, start the engine and run at low speed to make the oil pump work.

How to install and fix the hydraulic cylinder? There are two common ways to fix the hydraulic cylinder: the first is the square hydraulic cylinder fixed on the B plate, and the hydraulic cylinder needs to be positioned on the B plate. The second is a round hydraulic cylinder fixed on the ejector plate. It should be noted that the thimble plate locking screw needs to be added next to the hydraulic cylinder, and the force at this position is large, Yibin Oil cylinder Prevent tension deformation. Another point is to inscribe words on the hydraulic cylinder, and write down the stroke of the hydraulic cylinder for easy verification. To correctly install the sealing device at each position of the hydraulic cylinder: Yibin Oil cylinder Price When installing the O-ring seal, pay attention to its installation direction to avoid oil leakage due to installation. Its lip should face the oil chamber with pressure.

1、 If the groove is too deep, two situations will occur: A. If the gap between the seal root and the groove becomes larger, the seal root will become unstable. B. The interference between the sealing lip and the sealing surface becomes smaller, Yibin Oil cylinder The rebound force of the seal becomes smaller, and the failure rate of low-pressure oil leakage will increase when the piston rod jumps. 2、 If the groove is too shallow, two situations will also occur: A. The interference between the sealing lip and the sealing surface will increase, and the contact area will increase, which will lead to greater friction, Yibin Oil cylinder Price The increased heat accelerates the damage of the seal lip. B. As a result, the clearance at the seal root becomes smaller, and the probability of the seal root being squeezed out when the oil cylinder is under high pressure increases.

Compared with mechanical transmission, hydraulic cylinder transmission is a new transmission form. Hydraulic transmission has a history of more than 200 years since the birth of hydraulic press, but hydraulic transmission has been going on for many years. Especially after the 1960s, with the development of atomic energy science, space and hydraulic technology, Yibin Oil cylinder It permeates all fields of the national economy, including agricultural machinery, automobiles, light textile, shipbuilding, petroleum, aviation and machine tool industries, Yibin Oil cylinder Price Hydraulic technology lists some application examples of hydraulic and pneumatic transmission.

Select the cylinder type correctly according to the working requirements and conditions. It is required that there is no impact phenomenon and impact noise when the cylinder reaches the end of the stroke; Cushion cylinder shall be selected; Light weight is required; It is required to select light cylinder; Yibin Oil cylinder Narrow installation space and short stroke are required; It is required to select thin cylinder; It is required to have transverse load, and the cylinder with guide rod can be selected; High braking accuracy is required, and locking cylinder can be selected; It is not allowed to rotate the piston rod, and the cylinder with rod non rotation function can be selected; Yibin Oil cylinder Price In corrosive environment, corrosion-resistant steel cylinders shall be selected.

The two lips of the seal have two contact circumferential surfaces. Whether the force on the inner and outer circumferences is evenly distributed means that the force on the two circumferences cannot be zero. If the force on a certain point is zero, the shaft seal has inner and outer lips, Yibin Oil cylinder The outer lip is installed in the groove to contact the outer wall, and the inner lip is in contact with the piston rod surface. Both lips have an interference amount, which is equal to the generation of two contact circumferential surfaces, that is, the generation of two circumferential rebound forces. How to determine the magnitude of the circumferential force? Both the inner and outer lips of the seal have two chamfers. Since the interference of the same inner and outer lips is certain, Yibin Oil cylinder Price The angle of the chamfer determines the size of the circumferential area of the inner and outer contact of the two lips.